v4inktoneronlin's Journal [entries|friends|calendar] v4inktoneronlin [ userinfo | livejournal userinfo ] [ calendar | livejournal calendar ]

What’s the best way to use Your HP printer [27 Apr 2017|04:32pm] hp toner cartridges are the printer consumables of your HP LaserJet Printers, these contain toner powder made from high-engineered polymers mixed with carbon and coloring agents making the printing process possible. Its no surprise that users often complain how expensive these HP toners are, sometimes even to the extent that they cost higher than the laser printer unit itself. Thus to solve this dilemma, printer users resort in buying cost-saving alternative such as compatible HP toner cartridges to save money. But even though these compatible HP toners can lessen your printing expenses, don’t you wish to know how to extend the life of your toner cartridge to save even more. HP toner cartridges has a shelf life of about 18 months and an installed life of 6 months, basically having a life expectancy total of 24 months. However, as stated earlier, it is possible to extend this by following these certain steps: Store your HP toner cartridges properly. Since these printer cartridges are photo-sensitive, it is prudent to stock them on a dark cabinet at a room temperature of 60 to 78 degrees Fahrenheit. Remember to take note of the temperature, too much heat can cause the toner powder to melt and fuse within the cartridge’s parts. If this happens then there’s a great probability that your HP toner cartridges can be defunct. Popular hp printer models includes: cf400x / hp 201x, etc. Set your HP LaserJet to Eco-Mode. About a large portion of HP LaserJet Printers and multifunction centers are featured with an eco-mode setting. The Eco-Mode setting generates the printer to use minimal amount of toner in printing documents and images, thus saving the install life of your HP toner cartridges. For drafts and unimportant documents, print black. If you’re going to print for drafts, home works or full-text documents then select printing black in the printers setting since the normal setting tend to used all the colors thus wasting them. Redistribute the toner. A hack used to get the most out of your HP toner cartridges every time that low-toner alert message pops out in your screen. All you need to do is take out of the toner cartridge out of your printer component, gently shake it from side to side to distribute the toner powder inside the cartridge, making it possible for your printer to produce more output. While extending the life of the printer, you can also choose a more cost-effective supplies products to achieve the best results of the printer, which is the best use of HP printers. post comment

Best Toner Cartridge that go green [27 Apr 2017|04:28pm] Nowadays, green is one of the most important indicators in toner cartridge and other printer supplies. A lot of efforts are being made lately to reduce the use of harmful materials that cause trouble in the environment. Even when the technology is rising, there are still ways to conserve the resources and energy without having to lose the quality and life that you were used to. In the computer and printer industry, there are different ways being applied by several companies to go green. Some reduce their wastes through installing lightings that consume less energy. Also using cutting-edge LED can decrease your electric bill and lower the used materials for making electricity. Another method that many companies apply nowadays is reducing the trash made by being efficient with the internet communication and thinking twice before printing. Energy savings is also an important factor to save more on our resources. Low cost on electricity can be gained if the appliances used are those that are cost and Earth friendly. Also, turning off devices and lights not in use can really help especially in places that do not have too many of these left on. But if you wish to save on your work and personal prints, it’s very easy. Just use compatible cartridges like V4ink which can be an alternative for the expensive original equipment manufactured inks and toners. A compatible cartridge contributes to the saving of nature because of its manufacturing process and the resources it uses. It also saves on ink or toner while maintaining the high quality of printed materials. The popular printer models include brother toner / brother tn450 / cf400x, etc. Trying these measures will surely make you a more eco-friendly person plus you can save more on your electric bills too. That’s conserving money and the environment at the same time. post comment

Toner cartridges facing "growing demand" globally [09 Mar 2017|11:49am] A study of the global office stationery and supply market found that growing sales of printer cartridges in particular was one of the "top three emerging trends" worldwide. The study, by market analysts Technavio, analysed the "key trends expected to impact the market" from 2015 to 2019, with an emerging trend defined as "a factor that has the potential to significantly impact the market and contribute to its growth or decline". Of the top three emerging trends "impacting" the global market, Technavio named the "growing demand for computer/printer supplies", with ink cartridges pointed at in particular. The analysts stated that "IT integration and industry automation has driven the market for this segment", and added that "the toner cartridges category has become the largest contributor in this market as their demand is rising", with a compound annual growth rate (CAGR) of over nine percent through to 2019. Technavio also points to "leading manufacturers" including Brother, Canon, HP Inc and Epson, as well as "retailers like Staples, Office Depot and Walmart". Worldwide, the office stationery and supply market "is likely to exceed" 217 billion (€191 billion) by 2019 because "the developed markets for office stationery and supply products are growing at a very high rate", with particular markets seeing growth including the USA, UK, Germany, Canada, France and Japan, though "major growth is also expected" in developing markets such as China, Brazil, South Korea and India". The other two main trends the analysts have identified include "multichannel marketing", with various channels available "through the online or offline medium[s]", and "business expansion through mergers and acquisitions", a key theme for the remanufacturing industry of late. A fourth and lesser trend is that for "packaging innovation and green products", including recycled packaging and "green office supply products", which could include remanufactured cartridges. Brijesh Kumar Choubey, Senior Analyst at Technavio for the general retail goods and services industry, commented: "Although the demand for paper-based products is on the decline in developed markets due to industry automation and IT integration, growth prospects have increased for the printer and computer supplies manufacturers." post comment

How to Sell Toner Cartridge Online [09 Mar 2017|11:48am] There is big business in selling ink cartridges (http://www.v4ink.com/) online.After all, no one buys printer cartridge (http://www.v4ink.com/) just once. No, we need to keep buying it again and again while prices for printer ink cartridges (http://www.v4ink.com/) are simply too expensive at most brick-and-mortar stores. All of this equates to, as we said above, selling printer ink (http://www.v4ink.com/) online being big business. The ink market in the United States is over $6 billion dollars, and with consumers being able to print photos and color documents at home, the need for ink is not going away any time soon. However, none of this means that it is an easy business. You have got to approach selling ink toner and cartridges online in the right way. 1. Choose What to Sell Let's assume that you already know what you want to sell online: ink toner and cartridges. Now, you need to consider which ink toner and cartridge niche you want to focus upon. Odds are that you cannot offer all of them at this stage. A great way to identify what products are moving is to visit ebay and do an advanced search of "Sold Listings" for ink toner and ink cartridges. This will show you what the public wants. Since "Sold Listings" also shows what prices items sold for, you can see what prices you will need to source your ink toner at in order to make a profit by selling it at what people are willing to pay for it. Once you have identified a possible niche, buckle down and research it. Perhaps you have learned that drum cartridges for Brother Printers are prime movers. If so, you need to learn all that you can about these printers and their drum cartridges. You need to become the internet's go-to expert. 2. Pick the Right Domain Name for Your Ink Toner, Cartridge Online Store Okay. You have your niche, drum cartridges for Brother Printers, now you've got to choose a domain name. You need to select a name that tells your potential customers exactly what you do. Having a domain name that describes your business also helps your online business by increasing its search engine results page ranking, which is highly important in the online business game. Try to select a domain name that people will remember. 3. Build Your Ink Toner, Cartridge Online Store Whew... You've got your niche. You've got your name. All you need now is your online store. There are two ways to get this done: outsource the work or do it yourself. Regardless of which avenue you decide to travel there are some design principles that you absolutely have to follow. Make sure your color pallet matches your niche. An ink toner and cartridge online store would do well using the three primary color, red, yellow and blue. Also, this online store would need crisp, clear fonts and lines. Next, have your store set up so visitors can easily navigate it. A key to this is setting up your important information in an "F" pattern to take advantage of the way people's eyes tend to take in information. The designers at 3dcart are well aware of this key and a whole lot more. Our 50 plus design templates have all been designed with the customer in mind. 4. Get Payments Into Your Bank Account Getting paid is where the rubber hits the road. After all, until the cash starts coming in, your online store is a failure regardless of its name, niche, or design. Your goal as an online merchant is to make it as easy as possible for your customers and clients to pay. Two simple online payment solutions are PayPal and Google checkout. People trust them and they are easy to use. 3dcart stores come with both of these payment features built in. However, the drawback to PayPal and Google checkout is that they both direct customers to their sites to complete their payment, which, since it adds a step, is not as easy for your customer as it can be. To eliminate this extra step, go with a payment gateway option. 3dcart offers these as premium features. When you use a payment gateway, your customers are never directed away from your site. 5. Select Your Shipping Methods These days, as long as you are not selling large, bulky, and heavy items you need to give some serious consideration to offering free shipping. Odds are your competitors offer it. All of the major shipping services offer tracking features, which many customers really appreciate. 3dcart stores possess imbedded support for the major movers of products in North America to include FedEx, UPS, USPS, Canada Post and DHL. post comment

Reset Instruction of TN-450 & TN-660 Toner [09 Mar 2017|11:47am] Sometimes when we the machine does not work, the first thing that pops into our mind is that maybe it is time to replace the old machine by the new one. Likewise, when the warning light of "Toner Low", "Replace Toner" or "Toner Ended" keep popping up but you find that the printer cartridge is still lying in your printer, you cannot help yourself from questioning the quality of the toner and start to scold the printer seller. However, maybe the printer seller does not deserve your scold because usually, this kind of problem has nothing to do with the quality of the toner or the printer. A few steps to reset the ink cartridges can help you to get rid of those annoying "toner low" signals. For the Brother DCP/MFC Series printers: 1. Open the front toner compartment door. 2. The printer screen should read "front cover is open". 3. Press the "clear" button on the printer's front panel. 4. Printer will say "Replace Drum?" 5. Here do not press 1 but instead type in "*00" on the keypad. Star zero zero. 6. The screen will say "Accepted". Close the door and it will reset the low toner message. For the Brother HL Series printers: 1. Open front door. 2. Turn off printer. 3. While holding down the GO button, turn printer back on. 4. When all four LEDs light up release GO button. All LEDs will turn off. 5. Press the GO button 2 times. The 3 LEDs (toner, drum, paper) will light up solid. 6. Press the GO button 5 times. 7. Paper light will be blinking. 8. At this point the toner end-of-life condition has been reset. Close front door. Here is a little tip for you: timing is important here so don't pause between button presses. Besides, different printers and toners should be reset with different methods. The above method is suitable for the printer of Brother DCP/MFC/HL Series which should work with toner brother tn450 and brother tn 660. post comment

Get familiar with printer supplies-teach you how to repair the drum [08 Mar 2017|10:49am] Toner to the toner is to reduce the cost of printing the most important method. But the more the number of plus toner, toner cartridges will print quality is getting worse, generally when applied toner over two times, three times, when there will be some regular black spots, and this issue will With the increase in the number of print more and more serious. Finally, there will be printed documents blurred or print out a black mark, this time, the cartridge to scrapped, abandoned it is a pity, leaving useless, most people will choose at this time to replace the new ink cartridge. In fact, the old cartridge is still available, there are ways to repair, that is, renewable friends. Repaired after the print cartridge quality can also be comparable with the original cartridge, and the cost is only about a quarter of the original cartridge price. This is in line with environmental requirements, but also save our money. Hearing here, is not already heart it! Well, now let us together to waste cartridges to a "back to life." In fact, repair cartridge method can be divided into new toner and replace the photosensitive drum two parts. Following on in the usual HP 6L printer cartridges, for example, how we provide a method of regenerating the drum. First of all, to cut off the power to the printer, remove the print cartridge from the printer (this is of course, or else how to regenerate it), then pinch the side of the metal pin with a diagonal clamp, carefully pull out (or With metal nails pin into the cartridge, open the cartridge can be taken out after the metal pins), silver metal pins on both sides can be pulled out after the cartridge is divided into two parts, a light blue photosensitive selenium is a collection of waste powder part, While the one with the magnetic roller is the part for powder. And then part of the magnetic roller for the non-rotating side of the magnetic roller screw unscrew, take the plastic shell can be seen after a plastic cover, open the plastic cover, the toner cartridge and the magnetic roller on the clean up all the toner, Be sure to clean up all the residual toner, it is best to use a vacuum cleaner net absorption. Then the magnetic roller in the reverse order of just the right, this time should be held down by the magnetic roller to prevent the magnetic roller from the original position. The toner shaken slowly into the powder for the warehouse, a good plastic cover and plastic shell should pay attention to the magnetic roller on the axle at the end of the semicircle and plastic shell on the semi-circular holes on the good. Gently rotate the gears on the sides of the magnet roll to make the toner even. Now comes the most important step - the replacement of the new drum. The waste toner fixing pin fixed portion of the photosensitive drum with diagonal pliers to pull out (this can not be fixed with nails to pin into the drum where yo!), You can remove the old drum pulled out after fixing pin, and then the waste Powder collection part of the waste powder clean up. According to the demolition of anti-order put on a new drum, photosensitive drum installed to note that there is about the points, there will be side of the gear groove mounted groove. Then, fix the pin to fix the photosensitive drum. Newly purchased photographic drums have a black anti-exposure seal, do not torn off before installation to prevent exposure, to be installed after the check can be torn off. Finally, the powder part and the waste collection part of the open position by the installation of recovery, plug the metal on both sides of the card, you can start printing. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink: v4ink.com post comment

Get familiar with printer supplies-toner cartridge maintenance small recipe [08 Mar 2017|10:48am] 1, extend cartridge life (note: not necessarily valid) We know that the laser printer in the use of a longer period of time after the print out of the text, the image will appear blurred, bottom ash and other phenomena. Even if the replacement of a new toner cartridge is not solve the problem, then we should take into account the problem may be a cartridge. We know that laser printer toner cartridges have a life: more than 10,000 ships, such as Hewlett-Packard, Lenovo. When the life of the cartridge to a later, there will be the phenomenon. This is mainly due to photosensitive drum surface photosensitive properties of aging, the surface potential decline, the residual voltage increases, affecting the imaging cartridge caused by (see the first part of the printing principle). Is there any way to make the cartridge back to life? I thought of the surface of the cartridge is a layer of non-toxic organic compounds with photosensitive properties, when in the light, the coating will be conductive. In a number of chemical guidance of friends, I finally get it Cr2O3. As follows: Take to 5 g of chromium oxide, with lens paper dipped directly in one direction along the drum carefully wipe (do not wipe back and forth!) Again, to completely wipe the surface of the drum, do not miss. Wipe should be particularly careful: gentle, and then more gentle! Also note that your nails will scratch the drum tympanic membrane. Through the above-mentioned photosensitive drum can be re-printed thousands of pages to 10,000! What about it? You can save a lot of money, of course, this method may not be effective Oh. 2, full use of laser printer toner cartridges (Note: You can try) Since Epson (Epson) series laser printer with excellent print performance and convenient operation performance in the community there are a considerable number of users. But because of its more expensive supplies and the use of the cartridge is very easy to fatigue, when the fatigue, the drum surface can not be returned in the print media will leave a very "heavy" background, a direct impact on the print. Although the above mentioned also wipe with the chromium oxide cartridges, toner cartridge can eliminate the fatigue phenomenon, but this method may not be feasible. Because chromium oxide is solid particles (can not be dissolved), use it to wipe the surface of the drum, it may damage the drum surface. Some friends in the test of this method, but no effect, but the surface damage to the drum is very serious. After a number of tests, we also found a very simple method to eliminate the drum surface fatigue phenomenon, with this method, a cartridge can print more than 15,000 documents. Specific methods are as follows: When the drum fatigue phenomenon, the first to remove the cartridge shell, in order to prevent damage to the drum surface, a soft cloth can be used to wrap the drum surface, remove the shell, carefully remove the cartridge, the sun exposure To two hours, although the printer manual is strictly prohibited on the cartridge under the sun exposure. But this method is indeed valid, anyway, dead horse as a living horse to medicine it! And then poured waste toner powder box, a small screwdriver can be used in the waste toner box back and forth, the toner will soon come out, this will prevent the powder when confused full "dust" flying, will be poured out Of the toner collected up and down the toner cartridge, but also for you to save an expenditure. After cleaning the surface for a soft cloth and toner cartridges some of the parts, after the installation of a good cartridge, that you are done. Then you will be pleasantly surprised to find that the original unbearable purpose of the manuscript now "clear" visible, originally very "heavy" background wiped out. The above test is a friend's personal experience, each time can be successful, you may wish to try it effective! Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink: v4ink.com post comment

Using Your HP Toners to Their Full Potential [06 Mar 2017|09:42am] HP printers are one of the most popular printer brands in the world along Canon, Panasonic, Xerox, Brother and Epson. Hewlett Packard are also known for their laserjet printers, actually their were the one who introduced the first desktop laser printer to the world in the year 1984 and left an impact to the printing industry, giving a chance to the emergence of new laser-jet printers. hp toner are known for their durability and efficient functionality that provides printer users with satisfaction. These cartridges contain high-quality toner mixed with polymer that delivers excellent quality of printouts. They also provide you with high-yield and low-yield cartridges. High-yield toner cartridges allow you to print in large volumes but cost more than low-yield cartridges. Given that HP toners quality and performance are already proven by consumers, some things might intervene the performance of your HP toner cartridges that you need to avoid. Here are some tips to help you use your HP toners to their full potential: Take Note of Your HP Toner's Shelf Life – HP toners have an expected life of about 24 months divided between its shelf-life and installed life. The recommended shelf-life of an HP toner cartridge is about 18 months, while the remaining six months is the expected installed life of an HP toner. Avoid heat, moisture or humidity -Never expose your HP toners to excessive heat or humidity since this could damage their components and render their toner particles unfit for laser printing. Heat can cause toner to prematurely fuse with the plastic while moisture can turn the toner particles soggy and too much exposure on light can damage the photosensitive properties of your HP toners. Change the Cartridge DrumUnit – If your HP printer contains a separate drum, this drum needs to be replaced time to time. The average install life of an imaging drum last for three toner replacement. Most printer users make the mistake of replacing their toner cartridge instead of changing the printer's drum unit every time the printer prints sub-par quality documents. Never Leave them Behind – Never leave newly bought HP toners in your car, as even on cool days the temperature can exceed safe levels which may distort the plastic in the cartridge. The basement isn't a good place either because it's damp. Do Not Touch the Electric Component – Refrain yourself from touching the electric components of your HP toners, doing so may damage it and affect its performance. Just follow these tips and you're sure to be getting the best printouts from your HP toners. But most importantly, make sure you purchase your HP toners from reliable online retailers that only provides high-quality HP toners. V4ink is the leading specialist in providing quality compatible such as hp 201x for all HP printers. So grab your quality compatible HP toner from V4ink now! post comment

Office World Print Tips | Office Tips Print [06 Mar 2017|09:34am] Word as text editing tools most commonly used widely used in daily work and study. Along with the printing of the document naturally also has a small demand. Here we give a few to share Word printing techniques（recommend you brother toner）. 1. Reverse page order Print If you have a lot of pages of documents need to print, according to the Word the default settings are always printed from the first page to the last page, so the entire document is finished printing the last page at the top, at the bottom of the first page , So we have to manually order all the pages reverse side, very troublesome. In fact, before we print as long as the first in the "Tools" -> "Options" -> "Print" tab, select "Reverse page order to print", can in print in reverse order from the last page to print the first page, so After printing all the pages are arranged in sequence. 2. Use a different page orientation when you print the same document If you want to use both vertical and horizontal direction of two different pages in a document, we can first select the document needs to change direction, and then select "File" gt;? "Page Setup" command in the pop-up "page Set the desired page orientation in the Paper tab in the Settings dialog box, and select Selected Text in the Application tab. In fact, Word is the before and after the selection of each insert a section break, and only the contents of this section to change the page orientation, enabling to use different page orientation in the same document. 3. To avoid unnecessary additional information to print out Sometimes when printing an article will be inexplicable to print out some additional information, such as comments, hidden text, field codes. To avoid unnecessary additional information to print out, just before printing the "Tools" -> "Options" -> "Print" tab in the "additional information to print the document" does not select the appropriate keys. 4. Print formatted documents containing form Use in Word form to create formatted documents such as statistical tables and the like, other users can fill in the relevant information in specific places in the document, but can not change other content in a non-filled area. If you want to use a form containing a blank document has been printed in advance (ie fill area has not filled out) to print multiple copies of different statistical information, we can in the "Tools" -> "Options" -> "Print" option Card, select the "Print only form field content", so that when the form filled out the information, the print out will be filled out the information, rather than the entire statistical form of the document print out. 5. Print the document If you need a good editor with a Word document to print, but just with this computer and no printer, we can select the "Print" dialog box "Print to file" option, you can generate an input file name suffix named prn printer file, and on another computer equipped with a printer to print a document using the printer file, even if Word is not installed on that computer is required. 6. In print preview the document editing interface We generally in the print preview interface by zooming in and out to preview the final print results of the document, in fact, just click the print preview toolbar in the "magnifying glass" button (the button is not pressed state), you can print preview interface Directly edit the document, and not close the print preview. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink post comment

What is the cleaning method of the printer? [03 Mar 2017|10:16am] To clean the printer, several parts of the copier need to be separated in order to carry out targeted cleaning work. Editor to detail the various parts of the copier should be how clean. Copiers at least should be divided into three parts to clean, respectively, copier shell, copier glass panel, copier internal parts and toner cartridge. Here are the cleaning methods for each section: Cleaning method of the copier case The cover of the copier can be scrubbed with a semi-wet cloth. Be careful not to be too wet, the water dripping into the copier inside. If you encounter stubborn stains, you can gently wipe dipped in soapy water until the removal of stains so far, and then we have to use a cotton cloth dipped in water wipe several times, and finally dry with a dry cloth to complete the cleaning work. The most important thing to remember about cleaning a copier is cleaning it regularly to keep it clean. Cleaning method of glass panel for copier When cleaning the platen glass, avoid wiping with organic solvents. Because the platen glass is coated with a light-transmissive coating and a conductive coating, these coatings do not dissolve in water and are soluble in organic materials, so we do not use solvents such as alcohol to clean them. When using it, please avoid touching the table glass by hand. If there is binding, please remove the pins, paper clips and staples on the original and put it in the specified position. After the altered originals must wait until the correction fluid dry after copying. Cleaning of internal parts of copier We clean the internal parts of the copier to pay attention when wearing masks, so as not to smoke, such as dust. The most common part to remember is the fuser roller. Under normal circumstances I still suggest that if the dirty is directly replaced, because it is very difficult to clean up the printer toner on the stick. But if you can not find the replacement, you can try the day with water or gasoline bubble for a while, then wipe scrubbing, generally can remove the dust. In the removal of waste ink tube when you have to be careful to prevent the toner is filled in the air too much by the body inhalation. post comment

Color drum common bad printing phenomenon and causes [03 Mar 2017|10:16am] The following defect analysis is only for the toner cartridge, the production of some defects related to the machine, where omitted. 1) seal pull no: usually caused by poor assembly, seals a card or folded portions nipped toner. 2) powder leakage: In addition to bad seals seal before printing powder leakage caused by external and internal cartridge more components or parts during use may cause leakage of powder, magnetic roller felt seal defects, aging flour knife, seal roller blade deformation and Paste Not tightly loose, sealing sponge defects or aging, cleaning the blade deformation and paste loose loose and so will cause leakage powder. 3) not print either a full version or white light and vague; ● The seal is not opened. ● The toner cartridge does not shake before the seal, the powder is not smooth. ● The laser is not illuminated on the drum, the light shield is not open, and the drum protective cover is not open. ● Drum grounding is not connected, the drum conductive film or powder box on the machine connected to the electrical contact is bad. 4) Paper is usually black electrical problem: ● The charging roller is missing or defective. ● The charging roller is deformed or poorly connected. 5) Vertical black line: refers to any unwanted vertical lines from top to bottom, the thick line or wire may be continuous or the intermittent. The thin, light-colored vertical black line is generally a cleaning scraper gap or a circle of scratches on the drum. Thick and intermittent black line, and the edge is not clear, often sealed seal blade Zou or a knife caused by aging. 6) thin vertical white line on the blackboard: the depth of the wear line of the photosensitive drum with the magnetic roller magnetic roller coating or impurity caused by wear line. 7) levels were missing: finger prints on the lateral intermittent not print, because: ● Drum coating local exposure; ● Drum drive gear defects, loose or gear defect. ● magnetic roller coating defects; ● core fracture or positioning error; ● The magnetic roller sheath is badly worn or deformed. ● The magnetic roller conductive spring is in poor contact or beating. 8) horizontal black line: general electrical problem, periodically horizontal black line is often coupled with the charging roller coating defects caused by pinholes on the photosensitive drum coating; irregular horizontal black line is often thin bunker and waste toner binding Not in place caused. 9) periodically illegible: often the focus of the drum or cause pollution roll coating, watermarking, mimeograph, fingerprints, scratch marks often cited this defect. 10) bunches: a defect like money appear superimposed on the printed product, no rules, and difficult to repeat, drum caused by poor grounding. 11) Backscatter: refers to the surrounding text or lines do not need to have black specks, roller coating or toner by the magnetic drum overheating caused by poor (finger sensation and high) can also cause this defect. 12) Corrugated background (tiger grouper): black wavy white version appears on or in the form of white on black version or halftone version; usually a magnetic roller sleeve or coating defects due to normal low density printing, toner Bonding in the magnetic roller caused. 13) hollow words: Strokes text refers to the lack of the image on the lake, for the following reasons: ● toner itself. ● drum, powder with poor. Magnetic roller coating problem. ● The surface of the print media is too light and too strong. ● The paper uses the reverse side. 14) vertical black spots rules: ● by the sealing blade deformed or loose powder caused by scattered. ● As the powder knife aging or deformation, excessive accumulation of carbon in the drum roller, causing leakage powder. 15) Light color: with a variety of factors: ● Toner itself is a problem. ● Toner, magnetic roller with the problem. ● The aging of the knife. ● Magnetic roller wear. ● The life of the photoconductor drum. ● High humidity or moisture absorption. 16) bottom ash: bottom ash toner mist refers to a blank area of prints appear, but also with a variety of factors: ● Scraper aging loose. ● The charging roller is dirty. ● Toner problem. ● The environment is cold and dry. ● The print media is defective. ● Charging roller wear. ● fixing is not strong: refers to the print on the text or image that is to go. ● The toner softening point is higher than the fixing temperature of the machine. ● The print media is too thick or the surface is too light. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink 1 comment|post comment

User's Guide: How to Replace the Toner Cartridge on a Brother DCP-L2540DW Laser Multi-function Copie [02 Mar 2017|05:48pm] The Brother DCP-L2540DW is a dependable, economical monochrome laser multi-function copier for home or small office use. With its solid design and price tag, this copier is a desk-friendly machine that you can trust. It has an up to 250-sheet capacity tray, connects with ease via wireless networking or Ethernet, and prints and copies at up to 30ppm. It also has the ability to print from compatible mobile devices over your wireless network, and scan documents to a variety of destinations. The Brother DCP-L2540DW uses a tn660 toner (powder-based) instead of ink, so you get smudge-free images and text. Toners eventually run out after continued use. It is advisable to have an adequate printing supply in your home or office for maintaining operations. Stocking up on supplies will help to keep your copier running efficiently. V4ink offers a high quality replacement Brother TN660 black toner cartridge for the Brother DCP-L2540DW printer. This toner is professionally engineered to meet or exceed the genuine specifications and quality output of the Brother TN660. It offers a printing yield of up-to 2,600 pages ideal for high-volume printing. Being able to replace your copier's toner cartridge quickly and correctly lets you get back to work faster. If you are looking for quick and easy steps on how to replace the toner cartridge in your Brother DCP-L2540DW, follow the instructions below. Step 1 – Turn on your machine and open the front cover. Step 2 – Take the empty toner out by pushing down the lock lever on the drum unit assembly. It is a good idea to grab some paper towel just in case your old toner spills so you won't have a hard time cleaning it up on your table. Wrap up the empty toner before keeping it to somewhere safely. Step 3 – Unpack the new brother toner cartridge. Try shaking it a few times carefully before removing the orange shield or protector. It is actually quite possible that the powder substance inside it has settled during storage. Shaking allows the toner powder to spread evenly on the inside. thus, getting as many page prints as possible. Step 4 – Install the new toner by putting it into the drum unit. This should just fall into its position and snap into place. Step 5 – Move the corona wire cleaner back and forth several times and put the whole thing back into the machine then close the cover. The copier will then figure out for itself and detect the new toner installed. Press the "Go" button three times to print a test page. When it's done, then you're ready to go! If you want to stock up on replacement Brother TN660 black toner cartridge, V4ink has it for you at very low prices. Just check out our website for more options. We have compatible as well as genuine replacements available for your Brother DCP-L2540DW. post comment

Troubleshooting Tips [01 Mar 2017|05:41pm] Ink Cartridges Ink cartridge is leaking. Some of our cartridges may have been overfilled by the factory. We suggest you open the cartridges at a sink or over your garbage can to avoid possible leaks from damaging your valuable items. The internal pressure in the vacuum is not balanced. The cartridge should work fine anyway. Let the cartridge sit (printhead down) on a paper towel for a few minutes, then clean it up and install. (For a high temperature area) When the cartridge is opened, the ink may be bubbling/dripping out of the cartridge if it has been in a high temperature environment for a long time. This is because the heat creates pressure within the sealed cartridge and that pressure blows the ink out when the cartridge is opened. Please try chilling the cartridge in the refrigerator (not freezer) for a couple hours before use. Cartridge has a different shape The shape of our compatible cartridges may look a little different from OEM cartridges, but they are designed for use in your printer, and will fit. My cartridge won't fit Please make sure to remove the plastic protective case from the cartridge. Low ink message showing at the printer All of our cartridges are fully filled with ink. However, there are a small number of hp ink cartridgesthat may not have been reset fully during the remanufacturing process. Either bypass the low ink message or disable the ink level system on your printer. Although your printer will not track the ink levels, our cartridges will print fine from start to finish. On certain Epson and Lexmark printers, if the printer is saying you cannot print due to low ink, please press and hold the "stop" or "cancel" button for 10 seconds. This will reset the counter and allow you to use the cartridges normally. The print quality is not very good or the printout contains no ink Includes most Brother, Canon, Epson, and Xerox models. Make sure that you have removed the foil or plastic strip covering the vent hole and the nozzle. (Usually a bright color, but sometimes clear.) Make sure that the vent hole at the top of the cartridge and the nozzle are unblocked by any tape or plastic strip. To ensure that the vent hole is unobstructed, use a paper clip or another small, pointed object to probe the vent for blockages. Run the head cleaning cycle 2-3 times. Please make sure that the printer is set online (at the computer) and increase the darkness setting at the printer. If the color is still off, please install a whole set of our cartridges at your printer. It is possible that the formula of our ink is different from that of your original compatible cartridge. Note that Epson printers should be turned on and used at LEAST once a month, or preferably once a week. If the printer has not been used in over 5-6 months, Epson recommends that you replace the ink cartridges. Cheap toner cartridges can be found on V4ink website. post comment

How to check the ink or toner levels on my printer [27 Feb 2017|03:44pm] From the Systray Icon: None of the following steps work if you have not installed the software that was included with your printer. It's also important to note that every printer is different. These rules are meant as a general guideline. 1. Turn on the printer. 2. Locate the printer settings, often found by right-clicking the printer icon in the Systray, located in the bottom right-hand corner of your screen. 3. Within the printer settings software, you should see the toner levels for the currently installed printer cartridge. Below are a few different examples of how the ink level screens may look. Through the Windows Control Panel: The following steps will work for nearly any printer. However, if you have not installed the software that came with the printer, you may not be able to view the ink or toner levels. 1. Open the Control Panel. 2. Find and open the Printers option. 3. Right-click on the icon for the printer and select the Printer properties option. 4. Within the printer properties window, you can see the ink or toner levels for the currently installed hp ink cartridges. Through the Printer Menu: Keep in mind that every printer is different and the following steps are generalized. For explicit instructions on checking ink levels, consult your printer's documentation. 1. Turn your printer on. 2. Locate the Menu button and use the appropriate navigation keys to find a Status or Reports section. 3. Print a System Data or Status page to see current toner levels. If you want to order printer ink online, V4ink is the cheapest place to buy printer ink. post comment

Get familiar with printer supplies-the daily maintenance of toner cartridges [23 Feb 2017|09:51am] 1, the installation and storage Toner cartridge is an important component in the laser printer, a direct impact on the quality of printing. Cartridge installation is actually very simple, as long as the cartridge removed from the bag, out of the seal, and then to the drum axis axis rotation, the toner in the drum in the distribution, and then installed on the printer can be. As for the preservation of toner cartridge, in fact, more simple. As long as the cartridges stored in the original packaging bags, can be stored at room temperature. Do not let the sun direct exposure, otherwise it will affect the life of the cartridge. 2, maintenance issues As the laser printer imaging is dependent on the photoconductor drum exposure. When the toner cartridge encounters strong light, the inner and outer layers of the toner cartridge are turned on, so that the voltage of the toner cartridge is different from the voltage at the unexposed place, where the toner image can be attracted during the fixing process. However, a certain point of exposure to the drum time and the number of times are limited, especially in the long exposure to continuous damage to the cartridge more severe. So users usually should be used a lot of attention to the maintenance of toner cartridges. 1) Do not make the drum exposed to direct sunlight or other strong light sources. 2) Do not replace the toner cartridge in bright light, it should be as soon as possible to complete the installation process. 3) When the toner cartridge is removed from the printer, immediately put it back in the box or thick soft linen wrap. 4) If the toner cartridge from a cold place into a warm place and then set aside an hour or longer before use. 5) the drum light barrier shielded from external light source in order to protect the photosensitive drum, do not open the drum light barrier. 6) Do not touch the photosensitive drum surface by hand, and to prevent the drum surface to scratch hard objects. 7) Do not put the toner cartridge in a place of high temperature and high humidity. 8) to ensure that the cartridge away from the monitor, hard drive, floppy disk drive, or any other magnetic material. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink: v4ink.com post comment

Printer Not Recognizing Compatible Cartridges- 8 Steps To Take [23 Feb 2017|09:51am] Is your Samsung, HP, Brother, Canon, Ricoh or Epson printer not recognizing your new ink or toner cartridge? This is something that we find our customers experience every now and again so you definitely aren't alone! A printer not recognizing a new ink or toner cartridge is one of the most common issues that print owners experience when changing or replacing an empty one, irrespective of what brand printer you have, and one that our customers frequently ask us about. There may be occasions when, after installing a new ink or toner cartridge in your printer, you might see a message like: Your printer says 'toner is not compatible' Your printer says 'printer cartridge not detected' A low or empty level of ink and toner displayed on your computer A message on your printer warning "no cartridge installed" (or words to that effect) Flashing warning lights displayed on your printer Internal memory reset: Your printer should automatically recognize when you install a new cartridge and reset its internal memory, ensuring that it's displaying full ink and toner levels etc. However, sometimes the printer just doesn't do that correctly and believes that the old one, or no cartridge, is currently in there, instead. Protective strips: If you haven't removed protective covers or plastic strips that are attached to a new cartridge when you first take it out of its packaging, the printer will definitely fail to register the new cartridge. Dirty / damaged contacts: The canon printer ink or toner cartridge has a number of metal contacts that connect to similar metal contacts in the printer allowing them to communicate. Dirt or damage can prevent this. Firmware: Modern printers automatically connect to the internet but pc software or internal printer software (firmware) will often need to be updated. These updates can often fix bugs. Incorrect consumable installed: A rare occasion but this does happen! If a drum or fuser or other maintenance item was accidentally purchased instead of a toner or ink cartridge, the printer will not work and still needs a new ink or toner. So, here's what to do – 8 steps to try The first thing to do is not to panic! Whether you've bought them from us or another supplier, there really shouldn't be any reason why a good quality original or compatible cartridge wouldn't work in your printer so with a little patience, we'll get you through it. Try the following 8 steps to correct your issue. Resetting the printer memory: 1. Remove your new cartridge and replace it with the old one. Leave your printer and go and do something else for 10 minutes. 2. Replace the old cartridge with the Best Toner Cartridge again. These two steps alone often resolve the issue, so see if your printer now recognizes your new cartridges. However, if you're still having trouble… 3. Remove the new cartridge. Make sure you place it in a clean and safe place where the cartridge or the surface won't be damaged. 4. Turn the printer off button using its power button 5. Unplug your printer at the wall. It's important to do both steps 4 and 5 separately, as some printers can remain in sleep mode if you've only switched off the power button on the printer control panel. Leave your printer like this for about 10 minutes or so. 6. Plug your printer back in at the wall (but don't press the power button just yet) 7. Insert your new cartridge 8. Press the power button on your printer post comment

Causes and Solutions of No Paper Feed [22 Feb 2017|09:43am] 1, the paper put too much. First check that the paper is installed in accordance with the standard, such as whether the loading position has exceeded the left arrow arrow mark on the Printer, if more, you must reduce the printing paper. 2, blockage. To see if there is any foreign matter inside the printer block, for example, if the paper appears in the printer paper, it will lead to the phenomenon of not feeding. If there is a foreign object, it must be excluded, be sure to turn off the printer power, and then carefully remove the foreign body. If you want to remove the jammed paper, the paper must be along the direction of the paper slowly pull out, remove the paper after the paper also check whether there is residual shredding, and to ensure that the shredding is also cleared. 3, printing paper and wet. If you use the paper storage time is too long, and the surface has a wet feeling, there may be no paper into the phenomenon, this time we have to do is to dry the printing paper. 4, whether the ink runs out. The black or the ink cartridge's light flashes or flashes to indicate that the ink is nearly empty. If the ink cartridge is empty, the printer can not feed paper. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink post comment

My Samsung Laser Printer Is Printing Blank Pages [22 Feb 2017|09:42am] When your Samsung laser printer begins to print blank pages, it usually means that the printer's toner cartridge is running out of toner, the cartridge is defective and needs replacing or one or more components within your printer is faulty. Troubleshooting the printing problem is not difficult; you can usually resolve the problem yourself without consulting a repair service or center. Document Issue Your Samsung laser printer will print documents containing blank pages including entire documents containing blank pages, so it's possible the problem is not with your printer but with the document you are sending to the device. Check the document and delete any blank pages to resolve the printing problem before troubleshooting your printer's toner cartridge. Sealing Tape Issue If your samsung printer cartridge was recently replaced and is printing blank pages, remove the cartridge and check to see if you removed the sealing tape inserted into the cartridge. The sealing tape keeps toner from escaping the cartridge while within the cartridge's packaging. Open your Samsung printer's front cover, pull its toner cartridge out and pull the sealing tape out of the cartridge to resolve the printing issue. Reinstall the cartridge and resend the document you are trying to print to the printer. Out of Toner Issue Your Samsung laser printer's toner cartridge doesn't last forever and the cartridge may not always alert the printer that its toner level is low. This problem will result in blank documents no matter how many times you send a document from your computer to the printer. To squeeze the last bit of toner out of your printer's cartridge, open your Samsung printer's front cover, pull its toner cartridge out and shake the cartridge gently from side to side five to six times to distribute the toner inside of the cartridge. Hold the cartridge away from you to keep any loose toner from getting on your clothing. Do not touch the underside of the cartridge – this area makes contact with your printer and contains toner. Reinstall the toner cartridge once the toner is redistributed. You will be able to use your printer for a few more cycles, but will still have to replace the cartridge. Defective Toner Cartridge If the toner cartridge's sealing tape is not present and the cartridge is full of toner but still printing blank pages, the toner cartridge is defective and needs replacing. It could be that one or more components inside of the cartridge are failing or that the cartridge's electrical components are not communicating with your Samsung laser printer. Replace the cartridge immediately and try returning the defective cartridge for an exchange or refund. If you want to order printer ink online, V4ink would be the cheapest place to buy printer ink. Faulty Printer Components A faulty or defective printer controller or one or more defective circuit boards inside of your Samsung laser printer can cause the device to print blank pages. A faulty laser shutter, transfer roller or laser scanner cable might also cause your printer to print blank pages. Consult your Samsung laser printer's owner's manual or the Samsung website for a listing of authorized repair centers you can ship or take your printer to for repair. If the laser printer is still under warranty, the repair will be free but you may have to pay for shipping the printer to the repair center. post comment

Printer paper jam and its solution [21 Feb 2017|09:45am] Printer toner in the course of frequent use, often can not handle the paper failure, mostly paper jam, not into the paper, a paper into the multi-page and the phenomenon of random paper. How do these failures to deal with it after that? 　　 1, the paper surface is smooth. If the phenomenon of paper jams, first of all should see the paper surface is flat, if there is paper curl or fold phenomenon, it is best to use the surface smooth, smooth paper, and to ensure that the printing paper surface can not have a similar plastic adhesive. 　　 2, the paper is too thin or too much. Must ensure that the quality of printing paper more than 60 grams or more, the paper is too thin will cause the printer to become difficult when you take the paper, the printer is likely to cause a paper jam. And once into the printing paper can not be too thick. 　　 3, the pickup roller wear. The pick roller is the most wearable part of the printer. When the Sheng tray of normal paper, and can not take the paper, the paper roller is often wear or spring loose. Pressure is not enough, the paper can not be fed into the machine. Pickup roller wear, can not be replaced at the moment, the available wound rubber band approach for emergency treatment. Winding rubber band, the increase in the rubbing friction, make paper back to normal. 　　 4, other. Sheng tray is not properly installed, the paper quality is not good (too thin, too thick, wet), also may cause a paper jam or can not take the fault. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink post comment

How to Change a Samsung Cartridge [21 Feb 2017|09:44am] One of the easiest things you can do to keep your printer printing at an optimal level is to change the toner cartridge. Even if the printer is an all-in-one, like the Samsung SCX-4500W, the process can be completed with a few easy steps. And fortunately, you don't even have to guess when the time to change the cartridge comes. This model actually tells you it's time by displaying messages on its screen and by blinking LED lights on the control panel. To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Cover it with a piece of paper, if necessary. Do not touch the green area of the toner cartridge. Use the handle on the cartridge to avoid touching this area. Do not use sharp objects such as a knife or scissors to open the toner cartridge package. They might scratch the drum of the cartridge. If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into fabric. When opening a scan unit, hold the document feeder and scan unit together. How to Change a Samsung Toner Turn the printer's power off. The power button is located on the control panel on the top of the printer, on the right side. Open the printer's top cover by pressing the top cover lever, which is located on the bottom side of the top cover. Lift the cover all of the way open. Locate the toner cartridge. It will be right in the center of the printer and has a handle on the top of it. Grab the handle and pull the cartridge out. Hold the replacement cartridge at its side and gently rock it back and forth. This will help to distribute the toner equally throughout the cartridge. Remove the paper cover from the top of the cartridge. Insert the replacement cartridge into the printer and close the printer's top cover. Finally, V4ink is the cheapest place to buy printer ink. post comment

navigation [ viewing | most recent entries ] [ go | earlier ]