v4inktoneronlin's Journal [entries|friends|calendar]
v4inktoneronlin

[ userinfo | livejournal userinfo ]
[ calendar | livejournal calendar ]

Printer common jam resolution [20 Feb 2017|10:44am]
General Printer toner the most common fault is a paper jam, a lot of jam problems with the user's use of a relationship, for example, the paper is not put away is easy to jam and so on. If the user can learn some simple skills to deal with jam problems, then in everyday applications, it is easy to improve office efficiency. Here I share several common problems for the jam and solutions.

A multiple sheets feed reasons 4

1, the position of the paper. Position paper was placed incorrectly can cause multiple sheets feed occurs, correct height of the paper can not be higher than the arrow mark paper slot on the left rail; secondly, check the paper specifications meet the requirements: 60 to 180 wt. g paper in order to meet requirements, and less than 60 grams of thin paper, it is prone to the phenomenon of simultaneous multi-feed.

2, the surface of the printing paper curl. Curl is also caused by the occurrence of a multi-page paper, it must ensure that the paper surface smooth, if slightly curled, you can think of ways to flatten it.

3, electrostatic induction of. Electrostatic induction can also cause the phenomenon of multiple pages at a time, must be installed in the paper before the paper to spread out in a fan-shaped way to ensure that each paper can be separated separately, and then press the correct way to load paper into the guide In the bin.

4, adjust the position of the lever. For printers with paper thickness adjustment, it is important to adjust the position of the adjustment lever. When using a different paper, paper thickness lever position is not the same, for example, when using a conventional thickness of the paper, you must adjust the position of "0" bar. Of course, different printers on the regulation of the adjustment lever is not the same, the best reference manual.

When the printer to take the paper to print to a page when a piece of paper suddenly empty, and then automatically followed by printing down. This is often the printer to use for a long time, paper detection switch contacts due to wear and dust into the poor contact, resulting in the printer to make the wrong reasons to judge. Remove the printer, find the paper detection switch carefully cleaned with alcohol, can be restored to normal.

Printer ink refill, help you print high-quality documents, photos, and graphics.
Cheapest place to buy printer ink
post comment

Troubleshooting of Toner LED flashing [20 Feb 2017|10:43am]
I just replaced the tn450 toner cartridge and the LCD continues to display the message "Toner Low" / "Replace Toner" / "Toner Ended" or the Toner LED is still on or flashing.

If the machine's display or LED continues to show the Toner Low, Replace Toner or Toner Ended error indication after installing a new toner cartridge, follow the steps below to resolve the issue.

1.Verify that you didn't replace a different consumable by mistake.
The Brother machine has separate consumables - the toner cartridge and the drum unit. Verify you replace only the toner cartridge and not the drum unit.

2.Verify you are using a NEW Brother toner cartridge.
When replacing the toner cartridge, you MUST install a brand new, unused genuine Brother toner cartridge in order to reset the toner status. Swapping toner cartridges from one machine to another or installing a partially used toner cartridge may cause this issue. Brother machines control their image quality for the most suitable print quality by monitoring toner consumption. If you install a partially used toner cartridge, your Brother machine is unable to recognise toner consumption correctly which will cause this issue. Therefore, when you replace the toner cartridge, use a brand new toner cartridge, not a partially used toner cartridge from another machine.

3.Verify you are using a GENUINE Brother toner cartridge.
For optimum performance, use only new genuine Brother brand consumables which are specially formulated to ensure top print quality. Printing with non-Brother genuine toner cartridges may reduce not only the print quality but also the performance quality and life of the machine. If damage is caused to the drum unit or other parts of the machine as a result of using hp ink cartridges, any repairs required as a result will not be covered by the Brother limited warranty.

4.Verify the toner cartridge is installed correctly.
If you install a new genuine Brother toner cartridge but the "Toner Low", "Replace Toner" or "Toner Ended" error indication remains, the toner cartridge may not be installed correctly.
Reinstall the toner cartridge, referring to the instructions on how to replace the toner cartridge.

5.Clean the corona wire.
This issue may have occurred because the corona wire has become dirty.

6.Update the firmware to the latest version.
Go to the Downloads section of this website to check the latest version of the firmware.
If you see the Firmware Update Tool in the Downloads section, check detail information to identify the firmware version. If the firmware version of your Brother machine is earlier than the latest version, update the firmware. Follow the installation instructions on the download page.
post comment

How to Replace a Toner Cartridge in a Laser Printer [17 Feb 2017|09:44am]
Printer cartridge eventually run out of ink after continued use. Being able to replace them swiftly and correctly lets you get back to work faster. If you want to learn how to replace a toner cartridge in a laser printer, follow these steps.

1.Turn on the printer by pressing the power button. You have to have the device on to access brother toner cartridge of most units.
2.Open the printer door to access the toner cartridges. In some models, you will have to press and hold the release button and pull the lid toward you. When the cover is lifted on most laser printers, the carriage automatically slides to the right side of the unit for easy access to the cartridges.
3.Remove the spent cartridge from the printer. Depending on the model, you may have to unhook the cradle holding the cartridge in place, or press the release tab inward to unlatch the cartridge you want to remove. With some printers, you may have to hold down the blue release button at the side of the cartridge carriage. Once unlocked, remove the cartridge by pulling it up and toward you.
4.Take the new cartridge out of the box, but keep it in its plastic packaging. Sometimes, during shipping, ink can settle in the toner drum, resulting in poor-quality copies. To prevent this problem, gently shake the cartridge. This helps fully distribute toner throughout the cartridge.
5.Remove the new cartridge from its packaging and pull the colored tab on the cartridge. This removes the protective tape from the bottom of the cartridge. While doing this, be careful not to touch the imaging drum on the bottom of the print cartridge. Smudges on the drum can cause print-quality problems.
6.Put the replacement cartridge in. It should snap in place securely. On devices with a locking cradle, be sure to snap it shut around the cartridge before closing the lid.
7.Your printer is ready to be used. Print a test page. Your computer will automatically recognize that a new hp ink cartridges has been installed. Most computers will ask you if you want to print a test page to ensure that the new cartridge is functional. Click "OK." The computer will scan the printer settings and eventually produce a full-color page.
post comment

How to Replace Your Samsung Printer Cartridges [17 Feb 2017|09:44am]
Part of saving time is just being prepared. When an ink cartridge runs out, you don't want to have to drop everything and run to the store. If your office uses Samsung printers and supplies, you may want to get acquainted with Samsung printer cartridge replacement. When it's time to swap out an old printer cartridge, you can save time by following some simple steps. Here are some simple instructions for replacing your Samsung printer cartridges, so you can get back to printing.

Replacing Printer Cartridges:

1.Open the printer utility software. Samsung tries to make replacing samsung printer cartridge simpler by automating most of the steps for you. Explore your printer utility software and learn a bit more about how it works. To replace one of your Samsung printer cartridges, you'll need to open the cartridge replacement utility.
2.Move the cartridge head into place. Have your Samsung printer cartridges ready and follow the utility instructions to move the cartridge head into place.
3.Remove the old ink cartridge. Open the panel concealing the printer head and the old Samsung printer cartridges. Release the clips holding the empty one and pull it out. Remember to recycle your old Samsung printer cartridges. Samsung may even buy them back.
4.Prepare the new cartridge. Remove the appropriate Samsung printer cartridges from the packaging and shake them vigorously.
5.Insert the new cartridge. Remove the tag from the bottom of each Samsung ink cartridge, being careful not to touch any contacts or circuitry. Slip each cartridge into its space and press down until it clicks into place.
6.Close the printer. Close the printer lid or panel. The printer head should slide back into place and start charging your new cartridges.

Samsung Printer Cartridge Tips:
1.Samsung may recycle your hp 201x toner, or you can donate them to local recycling programs.
2.Unless your printer is malfunctioning, avoid printing test pages that can use a lot of ink.
post comment

Get familiar with printer supplies-choose a good cartridge [14 Feb 2017|11:09am]
At present, the laser printer cartridges are original

cartridges or other companies to produce a common cartridge and refill the cartridge three.

Now we will analyze the differences between these products.

We know that the print quality is certainly the first customer to consider the issue, no

doubt, the original cartridge is clearly the best choice. Original cartridge As the design

process carefully considered and other parts of the printer integration, the production

process is meticulous, it can also create the ideal print results, much better than other

compatible products. With the original print cartridge in the printer to print out the edge

of the text clear, black uniform, vivid picture, but the use of alternative products when

the effect will be far worse. This is because the original cartridges of the engineers in

order to print the best, in the laboratory for a lot of testing and improvement, even the

most minor defects must be removed and then fast. Therefore, the emphasis on print quality

users usually do not hesitate to select the original cartridge.

General generic cartridges in print quality can be said to achieve the basic requirements

of the printer output, but may differ in certain special circumstances, such as when

printing two pounds of fine words somewhat confusing. The refilled cartridge as a result of

the manufacturing process using a manual approach, print quality is good and bad, the

printing effect is difficult to be guaranteed. Of course, when we consider the quality of

print, print cost is also a very important consideration, especially for price-sensitive

individual users. Many people will think that the original product quality is good, but at

the same time the price is relatively high, this is actually an incorrect understanding, a

large number of objective tests show that the original single-page printing cost is not

high, the overall cost Is relatively low.

There is an independent research institutions have carried out an objective laser printer

toner comparison experiment. The results showed that, in comparison with the other two

original compatible cartridges, the original product cost per page and total cost of

ownership (TCO) minimum, a single drum is the largest number of copies, print quality is

the best.

Original cartridge due to the long service life, it saves the user money than the printer

itself, the price even more. Therefore, it is recommended to use the original cartridge.

Universal toner cartridge, from its print quality can be said to be able to achieve the

basic requirements of the laser printer output, but there may be a special case, the

distinction between generic toner cartridges are also produced brand name, product quality

is guaranteed, although its price Slightly lower than the original cartridge, but the

number of sheets to print less than the original cartridge, so the overall cost of printing

and original cartridge is almost the same.
As for the re-filling of the cartridge although the price is very attractive, but because

of its number of prints is too little or less than half of the original cartridge, so the

overall cost of printing is no less than the original cartridge and universal toner

cartridges.

Printer ink refill, help you print high-quality documents, photos, and graphics.
Cheapest place to buy printer ink: v4ink.com
post comment

Installation instruction of Brother TN420/TN450 [14 Feb 2017|11:05am]
These instructions explain toner installation procedures for a brother tn420 / tn450 toner cartridge.

The original toner cartridge that was included with this machine may either be a starter, standard, or a high yield cartridge. When the toner becomes low, the TONER LED indicator light will flash continuously until replaced. Once the toner cartridge is empty, the printer will enter a “REPLACE TONER” mode that ceases print functionality until the toner cartridge is replaced. A new and unused toner cartridge will reset the “REPLACE TONER” mode.

Before you begin please take time to perform the following steps to ensure that the new print cartridge is properly detected by your Brother printer:
1. Check to ensure that the dial on the left side of the brother toner cartridge is in the position as illustrated in the image below. If not, turn the dial counter clockwise until it matches the position in the image.
2. Check to make sure that the printer is powered up during the entire process. Changing the cartridge with the printer powered off will not reset the “REPLACE TONER” mode. In the event that the printer is powered off when the cartridge is installed, you will need to remove the cartridge and repeat step one before reinstalling the cartridge.

Replacing the toner cartridge

1. Make sure that the machine is powered up.
2. Open the front cover of the machine.
3. Remove both the drum unit and toner cartridge assembly.
4. Push down the green lock lever and take the toner cartridge out of the drum unit.
5. Unpack the new toner cartridge. Hold the cartridge level with both hands and gently shake it from side to side several times in order to distribute the toner evenly inside of the cartridge.
6. Pull off the protective cover.
7. Note: Before installing this cartridge, please check to ensure that the dial on the left side of the new cartridge is positioned identical to the image below. If not, turn the dial counter-clockwise until it matches the dial position in the image. It is imperative that this dial be locked into position as illustrated to ensure that the printer detects that a new cartridge has been installed and resets the “REPLACE TONER” mode.
8. Put the new toner cartridge firmly into the drum unit you hear and feel it lock into place. If installed successfully, the green lock lever will lift automatically.
9. Clean the primary corona wire inside of the drum unit by gently sliding the green tab from right to left and left to right several times.
10. Reinstall the drum unit and toner cartridge assembly back into the machine. Close the front cover.
post comment

Replacing the Toner Cartridge for HP Color LaserJet [13 Feb 2017|03:54pm]
This printer indicates when the hp ink level is low. The actual toner cartridge life remaining can vary. Consider having a replacement cartridge available to install when print quality is no longer acceptable. This printer uses four colors and has a different toner cartridge for each color: yellow (Y), magenta (M), cyan (C), and black (K). The toner cartridges are inside the front door of the printer.

Do not remove the toner cartridge from its package until it is time to install it. To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. If you remove the toner cartridge from the printer for an extended period of time, place the cartridge in the original plastic packaging, or cover the cartridge with a light-weight, opaque item. If toner gets on your clothing, wipe it off with a dry cloth and then wash the clothes in cold water. Hot water sets toner into fabric. Information about recycling used toner cartridges is in the toner cartridge box.

Follow these steps to replace the hp printer cartridges in your printer.
1. Open the front door.
2. Grasp the blue handle on the toner cartridge drawer, and then pull out the drawer.
3. Grasp the handle on the toner cartridge, and then pull the toner cartridge straight up to remove it.
4. Remove the new toner cartridge package from the box, and then pull the release tab on the packaging.
5. Remove the toner cartridge from the opened packaging shell.
6. Grasp both ends of the toner cartridge, and then gently rock the cartridge back and forth to distribute the toner.
7. Do not touch the imaging drum on the bottom of the toner cartridge. Fingerprints on the imaging drum can cause print quality problems.
8. Insert the new toner cartridge into the drawer. Make sure that the color chip on the cartridge matches the color chip on the drawer.
9. Push the toner cartridge drawer into the printer.
10. Close the front door.
post comment

Get familiar with printer supplies [10 Feb 2017|02:16pm]
We all know that the core component of the laser printer is the cartridge, toner cartridges directly affect the quality of the print, so we need to come to an independent understanding of the cartridge. This article includes the following four parts:

First, the importance of toner cartridges and toner

Before talking about toner cartridges, we need to briefly understand the relationship between toner cartridges and laser printers, we can first look at the laser printer works! The working principle of black and white laser printer, for example, when the computer sends data to the printer through the cable, the printer will first receive the data temporarily stored in the cache, when received a complete data sent to the printer after the processor, These data are processed into data sets of similar data tables that can be used to drive the print engine. For laser printers, these signals are a set of pulses that drive the laser head.

Well, laser printers began to work, in fact, the core technology is the electronic imaging technology, which combines the principles of imaging and electronics to generate images, the core component is a photosensitive cartridge. Laser emitters emit laser light on a prism-shaped mirror, with the rotation of the mirror, the light from one end of the drum to the other end in turn sweep (half way through a variety of focusing lens, so that the surface of the drum to scan the light is very small), then the drum to 1/300 inch or 1/600 inch stride is rotated and scanned line by line in the next performed. In fact, the drum is a surface coated with organic materials, cylinder, pre-charged with, when there is light exposure to the parts of the exposure will occur resistance of the reaction. The computer sends the data signal to control the laser emission, scanning the surface of the drum in the light constantly changing, so that some places will be exposed, the resistance is smaller, the charge disappeared, and some places are not subject to light exposure, Charge, and ultimately, the drum surface formed by the charge formed by the latent image. As shown in Fig.

How does the latent image become the actual printed image? Toner plays a key role in the toner is essentially a charge of fine plastic particles, the charge and the surface of the charge on the drum opposite polarity, when the surface of the drum with a charge through the ink roller, the charge The location of adsorption of toner particles, latent image becomes a real image. While the drum rotation, another group of transmission system will be sent to the printing paper, the print tape and the drum surface polarity of the same but much stronger charge, then the paper with toner cartridges, toner cartridges surface of the toner is attracted Onto the printing paper, the image is formed on the surface of the paper. At this time, the toner and the printer are merely attracted together by the attractive force of the charge, and the toner of the plastic mass is melted by heating at a high temperature before the printing paper is fed out to the printer, and solidifies on the surface of the paper sheet during the cooling.

After the toner is attached to the paper, the drum surface continues to rotate, passing through a cleaner that removes the remaining toner to enter the next print cycle. Can be seen in the process cartridge accounted for a very important position.

In fact, the laser printer is the most critical components. Because it not only determines the print quality is good or bad, but also determines the cost of printing. This is because the laser printer, 70% or more of the imaging units are concentrated in the drum, the print quality is good or bad in fact, it is largely determined by the cartridges. The cartridge and the printer is a consumable, the use of a period of time and reach a certain number of sheets after use need to be replaced, so choose the laser printer cartridge has a lot of knowledge.

Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink: v4ink.com
post comment

How do I clear the message "Replace Toner"? [10 Feb 2017|02:14pm]
The message "Replace Toner" is intended to alert you that the toner cartridge has reached the end of its expected life. It is recommended that the toner cartridge be replaced.

To clear the "Replace Toner" message, install a new genuine Brother TN420 or tn450 toner cartridge. When replacing the toner cartridge, you MUST install a brand new, unused genuine Brother toner cartridge in order to reset the "Replace Toner" status. Do NOT install a previously used cartridge that was already installed into another machine or a TN starter cartridge that comes with the machine.

Refer to the following solution for toner replacement instructions - "How do I install a new toner cartridge?

How do I replace the toner cartridge?"

The machine can be placed in Continue Mode. This is a temporary mode that will ensure that the current toner cartridge can continue to be used until the status changes to "Toner Ended" before you install a new toner cartridge.

Refer to the following solution for instructions to enable Continue Mode - "What is Toner Continue Mode?"

Brother strongly recommends that customers use only genuine Brother drum units and/or toner cartridges. Each Brother laser printer is designed to work at pre-set temperatures that are matched exactly to each of our individual toner formulations. Each individual component is designed to work with the other to ensure quality and reliability. Using non-Brother supplies may affect the hardware performance, print quality, and machine reliability. The Brother limited warranty does not apply to any problem that is caused by the use of third party drum units, ink cartridges, or toner.
post comment

Reset guide of Cf400x toner [06 Feb 2017|01:55pm]
Getting the toner cartridge (http://www.v4ink.com/) replacement process underway starts with a workspace that is free of clutter. Place newspaper or craft paper on a flat surface to catch any toner that may be spilled during the refilling process. It's probably best to empty the old remaining toner straight into a waste can to avoid spreading it around the room. It is also wise to wear disposable gloves when refilling printer cartridge (http://www.v4ink.com/)

Instructions for Refilling HP cf400x (http://www.v4ink.com/HP-CF400X-201X-Color-Toner-Cartridge) Cartridges with Refill Ports
Here are the steps to refilling HP ink cartridges (http://www.v4ink.com/) that have existing refill ports.

Some of the supplies that are required include:
• Phillips screwdriver
• Flat screwdriver
• Needle-nose pliers
• Toner
• Smart chip

1. Using the Philips screwdriver, remove the screws on the side of the cartridge to reveal the sealing plug. Position the flat screwdriver underneath the seal to gently loosen it. Use the needle-nose pliers to pull the plug off the cartridge.

2. Empty any toner left inside the cartridge. Before opening the bottle of toner, turn it upside down and tap it firmly on a flat surface to loosen the toner so that it will flow freely. Make sure that the cap is secure before tapping the bottle.

3. Tilt the cartridge to a 45-degree angle and fill the cartridge with toner.

4. Place the sealing plug back in its place and replace the smart chip on the cartridge before putting it back into the printer. The chip may need to be gently pried from its location. Insert the cartridge into the printer. Print a few pages to check the quality of the print.

Instructions for Replacing HP Laser Printer Cartridges Without Refill Ports
When the print cartridge does not have a refill port, the task becomes a bit harder, but can still be done. Some of the supplies needed are:
• Toner
• Universal toner cartridge hole-making tool
• Electrical tape
• Smart chip

1. Use a universal print cartridge (http://www.v4ink.com/) hole-making tool to create a hole in the cartridge. Remove the round plastic piece that will be burned out after the new hole has been made.

2. Empty all remaining original toner from the cartridge. Attach the pouring spout to the toner bottle, and refill the cartridge with toner. Seal the newly created hole with a small piece of electrical tape.

3. Replace the smart chip.
post comment

Installation Guide of Tn660 Toner [06 Feb 2017|01:55pm]
The Brother DCP-L2540DW is a dependable, economical monochrome laser multi-function copier for home or small office use. With its solid design and price tag, this copier is a desk-friendly machine that you can trust. It has an up to 250-sheet capacity tray, connects with ease via wireless networking or Ethernet, and prints and copies at up to 30ppm. It also has the ability to print from compatible mobile devices over your wireless network, and scan documents to a variety of destinations.
The Brother DCP-L2540DW uses a TN660 black toner (powder-based) instead of ink, so you get smudge-free images and text. Toners eventually run out after continued use. It is advisable to have an adequate printing supply in your home or office for maintaining operations. Stocking up on supplies will help to keep your copier running efficiently. V4ink offers a high quality replacement Brother TN660 toner cartridge(http://www.v4ink.com/Brother-TN660-TN630-Black-toner-cartridge) for the Brother DCP-L2540DW printer. This toner is professionally engineered to meet or exceed the genuine specifications and quality output of the brother tn 660(http://www.v4ink.com/Brother-TN630-TN660-Toner-Cartridge). It offers a printing yield of up-to 2,600 pages ideal for high-volume printing.
Being able to replace your copier’s toner cartridge (http://www.v4ink.com/) quickly and correctly lets you get back to work faster. If you are looking for quick and easy steps on how to replace the printer cartridge (http://www.v4ink.com/) in your Brother DCP-L2540DW, follow the instructions below.
Step 1 – Turn on your machine and open the front cover.
Step 2 – Take the empty toner out by pushing down the lock lever on the drum unit assembly. It is a good idea to grab some paper towel just in case your old toner spills so you won’t have a hard time cleaning it up on your table. Wrap up the empty toner before keeping it to somewhere safely.
Step 3 – Unpack the new ink cartridges (http://www.v4ink.com/). Try shaking it a few times carefully before removing the orange shield or protector. It is actually quite possible that the powder substance inside it has settled during storage. Shaking allows the toner powder to spread evenly on the inside. thus, getting as many page prints as possible.
Step 4 – Install the new toner by putting it into the drum unit. This should just fall into its position and snap into place.
Step 5 – Move the corona wire cleaner back and forth several times and put the whole thing back into the machine then close the cover.
The copier will then figure out for itself and detect the new toner installed. Press the “Go” button three times to print a test page. When it’s done, then you’re ready to go!
If you want to stock up on TN660 toner (http://www.v4ink.com/Brother-TN630-TN660-Toner-Cartridge), V4ink offers the cheapest place to buy printer ink(http://www.v4ink.com/Brother-TN630-TN660-Toner-Refill). Just check out our website for more options. We have compatible as well as genuine replacements available for your Brother DCP-L2540DW.
post comment

Reset Guide of Brother TN450 Toner [03 Feb 2017|04:48pm]
First, we will introduce you to the ink cartridges (http://www.v4ink.com/) basics. Each series mentioned here includes a standard yield and high yield cartridge option (we list the standard yield cartridge number first, followed by their high yield counterpart). The term high yield is used to describe printer ink cartridges (http://www.v4ink.com/) that contain more ink. If you are using a high yield printer cartridge (http://www.v4ink.com/) you will get more prints due to the higher ink capacity. The moderately filled standard print cartridge (http://www.v4ink.com/) is the most common option however, producing a smaller number of prints than the high yield. Consumers that only print on occasion will be happy investing in these less expensive cartridges, but if you print frequently, it’s probably better to go for the high yield. For example, the standard yield TN420 ( http://www.v4ink.com/Brother-TN420-TN450-Compatible-Toner-Cartridge) offers a yield of 1,200 pages, while the high yield TN450 (http://www.v4ink.com/Brother-TN420-TN450-Compatible-Toner-Cartridge) offers 2,600 pages. Compatible versions of the Brother brand are worth considering if you are looking to save some cash.
How To Reset Brother TN450 Toner:
The following is a step by step instruction on how to reset and install a new Brother TN450 Toner Cartridges:
To replace new toner cartridge, please remove old cartridge from the drum unit before installing new toner cartridge.
1. Toner sensor needs to be reset. Please do the following steps to reset the toner sensor.
2. Open the front cover and leave open while completing the following steps.
Turn the printer off.
Hold the ‘go’ button (or “start’ button) while turning the printer on. All panel lights should be on.
Release the ‘go’ button (or “start’ button).
Press the ‘go’ button (or “start’ button) 2 times.
Pause.
Press the ‘go’ button (or “start’ button) 5 times.
The toner light should be off.
The paper light should be on or flashing.
Close cover. The ready light should be the only light on.
3. If printer pops up errors, please check the gear of cartridge to see if it’s in the right place.
If it’s in wrong position, please use fingers to turn the gear anti-clockwise with 45 angles and this will be able to reset and put back to the printer for use..
post comment

Replacement Instruction of TN450 or TN420 printer cartridge [26 Jan 2017|11:56am]
Replacement Instruction of TN450 or TN420 printer cartridge(http://www.v4ink.com/)

If you have just replaced the toner cartridge (http://www.v4ink.com/) and the machine is still telling you to replace the printer ink (http://www.v4ink.com/), it is quite likely that the toner sensor flag on the side of the toner has not been “tripped” to recognize another toner has been replaced.
Check to ensure that the dial on the left side of the print cartridge (http://www.v4ink.com/) is in the position. If not, turn the dial counter clockwise until it matches the position. If not, turn the dial counter-clockwise until it matches the dial position. It is imperative that this dial be locked into position to ensure that the printer detects that a new cartridge has been installed and resets the “REPLACE TONER” mode. Check to make sure that the printer is powered up during the entire process. Changing the printer ink (http://www.v4ink.com/) with the printer powered off will not reset the “REPLACE TONER” mode. In the event that the printer is powered off when the printer ink cartridges (http://www.v4ink.com/) are installed, you will need to remove the cartridge and repeat step one before reinstalling the cartridge. Put the new toner cartridge firmly into the drum unit you hear and feel it lock into place. If installed successfully, the green lock lever will lift automatically.
People who use Brother Printers, which use Brother TN420 (http://www.v4ink.com/Brother-TN450-TN420-Toner-Cartridge-4-Pack) or TN450 (http://www.v4ink.com/Brother-TN420-TN450-Compatible-Toner-Cartridge) toner cartridges, might encounter toner error messages such as “Toner Low”, “Replace Toner” or “Toner Life End”. As the screen shows the cartridge you are using is empty or not recognized, you think you have to replace a new toner cartridge, or you cannot continue printing. But after installing a new cartridge, the problem still exists, and you will find that this happens with both OEM and compatible laser toner cartridges. It doesn’t mean the cartridge you bought is damaged, the reason is the cartridge didn’t reset properly, so the printer couldn’t recognize it as new one. Don’t worry, it is easy to reset.
For Brother HL Series:
1. Turn the printers power off.
2. Open the front cover to the toner/drum section of the printer.
3. Press and hold the “Go” button while turning on power to the printer.
4. Release the “Go” button after “Toner, Drum, and Error” LEDs turn on with the “Ready” LED turn off. All LEDs will now be OFF.
5. Press the “Go” button 2 times – The “Toner, Drum, and Error” LEDs will turn ON.
6. Press the “Go” button 6 times for a TN420 or Press the “Go” button 7 times for TN450.
7. Close the front cover after “Error” LED starts to flash.
8. The reset procedure has been completed.
post comment

Installation Instruction of Brother TN450/TN420 [25 Jan 2017|10:40am]
[ mood | безумное ]

Installation Instruction of Brother TN450/TN420 (http://www.v4ink.com/Brother-TN420-TN450-Compatible-Toner-Cartridge) Ink Cartridges (http://www.v4ink.com/)

These instructions explain toner installation procedures for a Brother TN420/TN450 toner cartridge. (http://www.v4ink.com/)
Introduction
The original printer cartridge(http://www.v4ink.com/) that was included with this machine may either be a starter, standard, or a high yield cartridge. When the toner becomes low, the TONER LED indicator light will flash continuously until replaced. Once the printer ink(http://www.v4ink.com/) is empty, the printer will enter a “REPLACE TONER” mode that ceases print functionality until the toner cartridge(http://www.v4ink.com/) is replaced. A new and unused toner cartridge will reset the “REPLACE TONER” mode.
Before You Begin
Before you begin please take time to perform the following steps to ensure that the new print cartridge (http://www.v4ink.com/)is properly detected by your Brother printer:
1. Check to ensure that the dial on the left side of the cartridge is in the position as illustrated in the image below. If not, turn the dial counter clockwise until it matches the position in the image.
2. Check to make sure that the printer is powered up during the entire process. Changing the printer ink cartridges (http://www.v4ink.com/)with the printer powered off will not reset the “REPLACE TONER” mode. In the event that the printer is powered off when the cartridge is installed, you will need to remove the cartridge and repeat step one before reinstalling the cartridge.

Replacing the Toner Cartridge
1. Make sure that the machine is powered up.
2. Open the front cover of the machine.
3. Remove both the drum unit and toner cartridge assembly.
4. Push down the green lock lever and take the toner cartridge out of the drum unit.
5. Unpack the new toner cartridge. Hold the cartridge level with both hands and gently shake it from side to side several times in order to distribute the toner evenly inside of the cartridge.
6. Pull off the protective cover.
7. Note: Before installing this cartridge, please check to ensure that the dial on the left side of the new cartridge is positioned identical to the image below. If not, turn the dial counter-clockwise until it matches the dial position in the image. It is imperative that this dial be locked into position as illustrated to ensure that the printer detects that a new cartridge has been installed and resets the “REPLACE TONER” mode.
8. Put the new toner cartridge firmly into the drum unit you hear and feel it lock into place. If installed successfully, the green lock lever will lift automatically.
9. Clean the primary corona wire inside of the drum unit by gently sliding the green tab from right to left and left to right several times.
Note: Be sure to return the tab to the home position (^) (1). If you do not, printed pages may contain a vertical stripe.
10. Reinstall the drum unit and toner cartridge assembly back into the machine. Close the front cover. Note: Do NOT turn off the machine’s power switch or open the front cover until the “Ready” LED has illuminated.

post comment

Summary of common faults of printer [24 Jan 2017|01:50pm]
[ mood | безумное ]

Summary of common faults of printer
Those who used HP/Canon ink jet printer might encounter some faults. How do we solve them?



What are the causes of printing stripes? How do we solve it?

Answer:
1. The air entered when installing the cartridge. We can solve it by cleaning the print head one or two times.
2. It may be caused by incorrectly installing the toner. Reinstall the toner and clean the print head one or two times.
3. The print head is old and required to change or mend.

The machine cannot identify the newly installed cf400x (http://www.v4ink.com/Hp-210x-CF400X-CF401X-CF402X-CF403X-Toner-Cartridges-Hp-210x-4-Pack) and 201x (http://www.v4ink.com/HP-CF400X-201X-Color-Toner-Cartridge) ink cartridges (http://www.v4ink.com/). How should we do?

Answer:
1. The cartridge with chip cannot be identified for hand touching chip or chip sticking dust. We can reinstall cartridge after wiping the chip with dry tissue.
2. The spring contact touching the chip on the print head is broken or damaged
3. There occurs elastic failure of spring plate on print head in the printer without chip.


The printed red picture is lighter than the one on computer, why and how do we solve it?

Answer:
The picture printed by a printer is not exactly the same as the actual image of the computer, which has a lot to do with computer graphics or its own pixels. If adjustments are needed, you can adjust color according with the needs through file→print→attribute→customize→advanced dialogue box.


When Epson printer is printing or copying, the computer prompts the non-original ink cartridges. Can we continue to use it?

Answer:
The Epson manufacturers set it up on the printer. When non-original-cartridge is prompted, click yes. It would not have any influence on the printing of toner.


A month ago EPSON C20 printer can be used normally. But it cannot print after being idle for a month.

Answer:
Without using the printer for a long time, the print head may get dry. You can solve the problem by cleaning the print head. Even if you do not use the printer, for best quality of printing, we recommend that the machine be able to run once a week to fill the machine with ink. This is good for the maintenance of machine.

post comment

Knowhow of Installing Brother TN450 TN420 Compatible Toner Cartridge [24 Jan 2017|01:48pm]
[ mood | безумное ]

Knowhow of Installing Brother TN450 TN420
(http://www.v4ink.com/Brother-TN420-TN450-Compatible-Toner-Cartridge) Compatible Toner Cartridge


I own an Brother-DCP-7060D Monochrome Multifunction Laser Printer. It can scan documents in 3 seconds and print extremely fast with great quality. It is easy to operate. Toner replacements are not very expensive. But I have to learn how to install brother tn420 (http://www.v4ink.com/Brother-TN450-TN420-Toner-Cartridge-4-Pack) toner cartridge in the printer. First of all, I found the cheapest place to buy printer ink (http://www.v4ink.com/Brother-TN630-TN660-Toner-Refill) on the website www.v4ink.com.
How to Install a Brother TN420 Toner.
Note: Before doing anything else, make sure that the Brother printer is powered and on during the process. Changing the cartridge with the power off will not reset the replace toner mode of the printer, causing the printer not to recognize the new toner cartridge.
Step 1 – Open the front panel of your Brother laser printer and carefully remove the DR-420 drum from the printer.
Step 2 – Press the green tab in the DR-420 drum unit to release the Brother TN420 toner cartridge from it.
Step 3 – Install the new Brother TN420 toner cartridge. Note that the TN420 toner cartridge and the DR-420 drum unit are purchased separately. Once you hear a small click on the drum cartridge that indicates your TN-420 toner cartridge is already locked in place.
Step 4 – Finally, install the DR-420 drum unit into the Brother laser printer and firmly close the front panel. And you can check your printer’s setting now to see if the printer had recognized the new Brother TN420 toner cartridge. Once you everything’s okay, you can finally proceed in printing your documents.
For quality Brother TN420 toner cartridge and DR-420 drum unit that won’t cost a fortune, visit V4ink.com. V4ink offers a great selection of Brother toners, ink cartridges and drum cartridges. Whether you are looking for compatible or OEM cartridges or black and color cartridges for your Brother printers, V4ink got it covered.
I highly recommend V4ink compatible cartridges as they are professionally built, guaranteed to match OEM cartridge performance and, of course, cheap toner cartridges (http://www.v4ink.com/Brother-TN450-TN420-Toner-Cartridge-Cheap-Toner-Cartridges). And without any question or extra fee asked, V4ink will ship a replacement cartridge on your way as fast as they can. Because that is how V4ink prioritize and value their customers.

post comment

Problems related to replacement of printer cartridge [24 Jan 2017|01:44pm]
[ mood | безумное ]

Problems related to replacement of printer cartridge(http://www.v4ink.com/)
This year I bought a Brother printer, but a month after I used the printer I encountered the replacement problem of toner cartridges. The first question that happened to me is where is the cheapest place to buy printer ink (http://www.v4ink.com/Brother-TN660-Compatible-Toner-Cartridge). Then I googled it and finally found V4ink.com. I placed an order of brother tn 660 (http://www.v4ink.com/Brother-TN630-TN660-Toner-Cartridge) on the V4ink website. The delivery service is good so that several days later I received the product. It is the first time for me to replace printer ink (http://www.v4ink.com/). So I learned how to install printer cartridge properly online: first, your printer ink cartridges will last longer if you do not remove your cartridge from the protective wrapping until it's ready for use; Second, the ink cartridge should be placed upright for at least 30 minutes prior to use, which will allow the ink to flow down to the print head and allow any oxygen bubbles to rise up and away from the print head; Third, be sure you've removed the plastic strip from the ink cartridge; Fourth, install the print cartridge; Fifth, run the head cleaning cycle at least one time; Sixth, print a test page to make sure the print cartridges are installed and functioning properly. I just replaced the toner cartridge and the LCD continues to display the message "Toner Low" and the Toner LED is still flashing. Then I verify I replaced only the toner cartridge and not the drum unit since the Brother machine has separate consumables - the toner cartridge and the drum unit. When replacing the toner cartridge, I installed a brand new, unused genuine Brother toner cartridge in order to reset the toner status. Swapping toner cartridges from one machine to another or installing a partially used toner cartridge may cause this issue. Brother machines control their image quality for the most suitable print quality by monitoring toner consumption. If you install a partially used toner cartridge, your Brother machine is unable to recognise toner consumption correctly which will cause this issue. If you install a new genuine Brother toner cartridge but the "Toner Low", "Replace Toner" or "Toner Ended" error indication remains, the toner cartridge may not be installed correctly.
Reinstall the toner cartridge, referring to the instructions on how to replace the toner cartridge. That is how I solved the problem.

post comment

navigation
[ viewing | 20 entries back ]
[ go | later ]