| Troubleshooting of Toner LED flashing |
[20 Feb 2017|10:43am] |
I just replaced the tn450 toner cartridge and the LCD continues to display the message "Toner Low" / "Replace Toner" / "Toner Ended" or the Toner LED is still on or flashing.
If the machine's display or LED continues to show the Toner Low, Replace Toner or Toner Ended error indication after installing a new toner cartridge, follow the steps below to resolve the issue.
1.Verify that you didn't replace a different consumable by mistake.
The Brother machine has separate consumables - the toner cartridge and the drum unit. Verify you replace only the toner cartridge and not the drum unit.
2.Verify you are using a NEW Brother toner cartridge.
When replacing the toner cartridge, you MUST install a brand new, unused genuine Brother toner cartridge in order to reset the toner status. Swapping toner cartridges from one machine to another or installing a partially used toner cartridge may cause this issue. Brother machines control their image quality for the most suitable print quality by monitoring toner consumption. If you install a partially used toner cartridge, your Brother machine is unable to recognise toner consumption correctly which will cause this issue. Therefore, when you replace the toner cartridge, use a brand new toner cartridge, not a partially used toner cartridge from another machine.
3.Verify you are using a GENUINE Brother toner cartridge.
For optimum performance, use only new genuine Brother brand consumables which are specially formulated to ensure top print quality. Printing with non-Brother genuine toner cartridges may reduce not only the print quality but also the performance quality and life of the machine. If damage is caused to the drum unit or other parts of the machine as a result of using hp ink cartridges, any repairs required as a result will not be covered by the Brother limited warranty.
4.Verify the toner cartridge is installed correctly.
If you install a new genuine Brother toner cartridge but the "Toner Low", "Replace Toner" or "Toner Ended" error indication remains, the toner cartridge may not be installed correctly.
Reinstall the toner cartridge, referring to the instructions on how to replace the toner cartridge.
5.Clean the corona wire.
This issue may have occurred because the corona wire has become dirty.
6.Update the firmware to the latest version.
Go to the Downloads section of this website to check the latest version of the firmware.
If you see the Firmware Update Tool in the Downloads section, check detail information to identify the firmware version. If the firmware version of your Brother machine is earlier than the latest version, update the firmware. Follow the installation instructions on the download page.
|
|
| Printer common jam resolution |
[20 Feb 2017|10:44am] |
General Printer toner the most common fault is a paper jam, a lot of jam problems with the user's use of a relationship, for example, the paper is not put away is easy to jam and so on. If the user can learn some simple skills to deal with jam problems, then in everyday applications, it is easy to improve office efficiency. Here I share several common problems for the jam and solutions.
A multiple sheets feed reasons 4
1, the position of the paper. Position paper was placed incorrectly can cause multiple sheets feed occurs, correct height of the paper can not be higher than the arrow mark paper slot on the left rail; secondly, check the paper specifications meet the requirements: 60 to 180 wt. g paper in order to meet requirements, and less than 60 grams of thin paper, it is prone to the phenomenon of simultaneous multi-feed.
2, the surface of the printing paper curl. Curl is also caused by the occurrence of a multi-page paper, it must ensure that the paper surface smooth, if slightly curled, you can think of ways to flatten it.
3, electrostatic induction of. Electrostatic induction can also cause the phenomenon of multiple pages at a time, must be installed in the paper before the paper to spread out in a fan-shaped way to ensure that each paper can be separated separately, and then press the correct way to load paper into the guide In the bin.
4, adjust the position of the lever. For printers with paper thickness adjustment, it is important to adjust the position of the adjustment lever. When using a different paper, paper thickness lever position is not the same, for example, when using a conventional thickness of the paper, you must adjust the position of "0" bar. Of course, different printers on the regulation of the adjustment lever is not the same, the best reference manual.
When the printer to take the paper to print to a page when a piece of paper suddenly empty, and then automatically followed by printing down. This is often the printer to use for a long time, paper detection switch contacts due to wear and dust into the poor contact, resulting in the printer to make the wrong reasons to judge. Remove the printer, find the paper detection switch carefully cleaned with alcohol, can be restored to normal.
Printer ink refill, help you print high-quality documents, photos, and graphics.
Cheapest place to buy printer ink
|
|