v4ink_toner's Journal [entries|friends|calendar] v4ink_toner [ website | My Website ] [ userinfo | livejournal userinfo ] [ calendar | livejournal calendar ]

What is the cleaning method of the printer? [07 Mar 2017|10:33am] To clean the printer, several parts of the copier need to be separated in order to carry out targeted cleaning work. Editor to detail the various parts of the copier should be how clean. Copiers at least should be divided into three parts to clean, respectively, copier shell, copier glass panel, copier internal parts and samsung toner cartridge. Here are the cleaning methods for each section: Cleaning method of the copier case The cover of the copier can be scrubbed with a semi-wet cloth. Be careful not to be too wet, the water dripping into the copier inside. If you encounter stubborn stains, you can gently wipe dipped in soapy water until the removal of stains so far, and then we have to use a cotton cloth dipped in water wipe several times, and finally dry with a dry cloth to complete the cleaning work. The most important thing to remember about cleaning a copier is cleaning it regularly to keep it clean. Cleaning method of glass panel for copier When cleaning the platen glass, avoid wiping with organic solvents. Because the platen glass is coated with a light-transmissive coating and a conductive coating, these coatings do not dissolve in water and are soluble in organic materials, so we do not use solvents such as alcohol to clean them. When using it, please avoid touching the table glass by hand. If there is binding, please remove the pins, paper clips and staples on the original and put it in the specified position. After the altered originals must wait until the correction fluid dry after copying. Cleaning of internal parts of copier We clean the internal parts of the copier to pay attention when wearing masks, so as not to smoke, such as dust. The most common part to remember is the fuser roller. Under normal circumstances I still suggest that if the dirty is directly replaced, because it is very difficult to clean up the printer toner on the stick. But if you can not find the replacement, you can try the day with water or gasoline bubble for a while, then wipe scrubbing, generally can remove the dust. In the removal of waste ink tube when you have to be careful to prevent the toner is filled in the air too much by the body inhalation. 1 comment|post comment

Using Your HP Toners to Their Full Potential [07 Mar 2017|10:30am] HP printers are one of the most popular printer brands in the world along Canon, Panasonic, Xerox, Brother and Epson. Hewlett Packard are also known for their laserjet printers, actually their were the one who introduced the first desktop laser printer to the world in the year 1984 and left an impact to the printing industry, giving a chance to the emergence of new laser-jet printers. HP toner are known for their durability and efficient functionality that provides printer users with satisfaction. These cartridges contain high-quality toner mixed with polymer that delivers excellent quality of printouts. They also provide you with high-yield and low-yield cartridges. High-yield toner cartridges allow you to print in large volumes but cost more than low-yield cartridges. Given that HP toners quality and performance are already proven by consumers, some things might intervene the performance of your HP toner cartridges that you need to avoid. Here are some tips to help you use your HP toners to their full potential: Take Note of Your HP Toner’s Shelf Life - HP toners have an expected life of about 24 months divided between its shelf-life and installed life. The recommended shelf-life of an HP toner cartridge is about 18 months, while the remaining six months is the expected installed life of an HP toner. Avoid heat, moisture or humidity - Never expose your HP toners to excessive heat or humidity since this could damage their components and render their toner particles unfit for laser printing. Heat can cause toner to prematurely fuse with the plastic while moisture can turn the toner particles soggy and too much exposure on light can damage the photosensitive properties of your HP toners. Change the Cartridge DrumUnit - If your HP printer contains a separate drum, this drum needs to be replaced time to time. The average install life of an imaging drum last for three toner replacement. Most printer users make the mistake of replacing their toner cartridge instead of changing the printer’s drum unit every time the printer prints sub-par quality documents. Never Leave them Behind - Never leave newly bought HP toners in your car, as even on cool days the temperature can exceed safe levels which may distort the plastic in the cartridge. The basement isn’t a good place either because it’s damp. Do Not Touch the Electric Component - Refrain yourself from touching the electric components of your HP toners, doing so may damage it and affect its performance. Just follow these tips and you’re sure to be getting the best printouts from your HP toners. But most importantly, make sure you purchase your HP toners from reliable online retailers that only provides high-quality HP toners. V4ink is the leading specialist in providing quality compatible such as hp 201x for all HP printers. So grab your quality compatible HP toner from V4ink now! 1 comment|post comment

Color drum common bad printing phenomenon and causes [06 Mar 2017|03:41pm] The following defect analysis is only for the toner cartridge, the production of some defects related to the machine, where omitted. 1) seal pull no: usually caused by poor assembly, seals a card or folded portions nipped toner. 2) powder leakage: In addition to bad seals seal before printing powder leakage caused by external and internal cartridge more components or parts during use may cause leakage of powder, magnetic roller felt seal defects, aging flour knife, seal roller blade deformation and Paste Not tightly loose, sealing sponge defects or aging, cleaning the blade deformation and paste loose loose and so will cause leakage powder. 3) not print either a full version or white light and vague; ● The seal is not opened. ● The toner cartridge does not shake before the seal, the powder is not smooth. ● The laser is not illuminated on the drum, the light shield is not open, and the drum protective cover is not open. ● Drum grounding is not connected, the drum conductive film or powder box on the machine connected to the electrical contact is bad. 4) Paper is usually black electrical problem: ● The charging roller is missing or defective. ● The charging roller is deformed or poorly connected. 5) Vertical black line: refers to any unwanted vertical lines from top to bottom, the thick line or wire may be continuous or the intermittent. The thin, light-colored vertical black line is generally a cleaning scraper gap or a circle of scratches on the drum. Thick and intermittent black line, and the edge is not clear, often sealed seal blade Zou or a knife caused by aging. 6) thin vertical white line on the blackboard: the depth of the wear line of the photosensitive drum with the magnetic roller magnetic roller coating or impurity caused by wear line. 7) levels were missing: finger prints on the lateral intermittent not print, because: ● Drum coating local exposure; ● Drum drive gear defects, loose or gear defect. ● magnetic roller coating defects; ● core fracture or positioning error; ● The magnetic roller sheath is badly worn or deformed. ● The magnetic roller conductive spring is in poor contact or beating. 8) horizontal black line: general electrical problem, periodically horizontal black line is often coupled with the charging roller coating defects caused by pinholes on the photosensitive drum coating; irregular horizontal black line is often thin bunker and waste toner binding Not in place caused. 9) periodically illegible: often the focus of the drum or cause pollution roll coating, watermarking, mimeograph, fingerprints, scratch marks often cited this defect. 10) bunches: a defect like money appear superimposed on the printed product, no rules, and difficult to repeat, drum caused by poor grounding. 11) Backscatter: refers to the surrounding text or lines do not need to have black specks, roller coating or toner by the magnetic drum overheating caused by poor (finger sensation and high) can also cause this defect. 12) Corrugated background (tiger grouper): black wavy white version appears on or in the form of white on black version or halftone version; usually a magnetic roller sleeve or coating defects due to normal low density printing, toner Bonding in the magnetic roller caused. 13) hollow words: Strokes text refers to the lack of the image on the lake, for the following reasons: ● toner itself. ● drum, powder with poor. Magnetic roller coating problem. ● The surface of the print media is too light and too strong. ● The paper uses the reverse side. 14) vertical black spots rules: ● by the sealing blade deformed or loose powder caused by scattered. ● As the powder knife aging or deformation, excessive accumulation of carbon in the drum roller, causing leakage powder. 15) Light color: with a variety of factors: ● Toner itself is a problem. ● Toner, magnetic roller with the problem. ● The aging of the knife. ● Magnetic roller wear. ● The life of the photoconductor drum. ● High humidity or moisture absorption. 16) bottom ash: bottom ash toner mist refers to a blank area of prints appear, but also with a variety of factors: ● Scraper aging loose. ● The charging roller is dirty. ● Toner problem. ● The environment is cold and dry. ● The print media is defective. ● Charging roller wear. ● fixing is not strong: refers to the print on the text or image that is to go. ● The toner softening point is higher than the fixing temperature of the machine. ● The print media is too thick or the surface is too light. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy best toner cartridge 1 comment|post comment

Office World Print Tips | Office Tips Print [06 Mar 2017|03:37pm] Word as text editing tools most commonly used widely used in daily work and study. Along with the printing of the document naturally also has a small demand. Here we give a few to share Word printing techniques（recommend you brother toner）. 　　 1. Reverse page order Print If you have a lot of pages of documents need to print, according to the Word the default settings are always printed from the first page to the last page, so the entire document is finished printing the last page at the top, at the bottom of the first page , So we have to manually order all the pages reverse side, very troublesome. In fact, before we print as long as the first in the "Tools" -> "Options" -> "Print" tab, select "Reverse page order to print", can in print in reverse order from the last page to print the first page, so After printing all the pages are arranged in sequence. 　　 2. Use a different page orientation when you print the same document If you want to use both vertical and horizontal direction of two different pages in a document, we can first select the document needs to change direction, and then select "File" gt;? "Page Setup" command in the pop-up "page Set the desired page orientation in the Paper tab in the Settings dialog box, and select Selected Text in the Application tab. In fact, Word is the before and after the selection of each insert a section break, and only the contents of this section to change the page orientation, enabling to use different page orientation in the same document. 　　 3. To avoid unnecessary additional information to print out Sometimes when printing an article will be inexplicable to print out some additional information, such as comments, hidden text, field codes. To avoid unnecessary additional information to print out, just before printing the "Tools" -> "Options" -> "Print" tab in the "additional information to print the document" does not select the appropriate keys. 　　 4. Print formatted documents containing form Use in Word form to create formatted documents such as statistical tables and the like, other users can fill in the relevant information in specific places in the document, but can not change other content in a non-filled area. If you want to use a form containing a blank document has been printed in advance (ie fill area has not filled out) to print multiple copies of different statistical information, we can in the "Tools" -> "Options" -> "Print" option Card, select the "Print only form field content", so that when the form filled out the information, the print out will be filled out the information, rather than the entire statistical form of the document print out. 　　 5. Print the document If you need a good editor with a Word document to print, but just with this computer and no printer, we can select the "Print" dialog box "Print to file" option, you can generate an input file name suffix named prn printer file, and on another computer equipped with a printer to print a document using the printer file, even if Word is not installed on that computer is required. 　　 6. In print preview the document editing interface We generally in the print preview interface by zooming in and out to preview the final print results of the document, in fact, just click the print preview toolbar in the "magnifying glass" button (the button is not pressed state), you can print preview interface Directly edit the document, and not close the print preview. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer toner 1 comment|post comment

User's Guide: How to Replace the Toner Cartridge on a Brother DCP-L2540DW Laser Multi-function Copie [03 Mar 2017|10:04am] The Brother DCP-L2540DW is a dependable, economical monochrome laser multi-function copier for home or small office use. With its solid design and price tag, this copier is a desk-friendly machine that you can trust. It has an up to 250-sheet capacity tray, connects with ease via wireless networking or Ethernet, and prints and copies at up to 30ppm. It also has the ability to print from compatible mobile devices over your wireless network, and scan documents to a variety of destinations. The Brother DCP-L2540DW uses a tn660 toner (powder-based) instead of ink, so you get smudge-free images and text. Toners eventually run out after continued use. It is advisable to have an adequate printing supply in your home or office for maintaining operations. Stocking up on supplies will help to keep your copier running efficiently. V4ink offers a high quality replacement Brother TN660 black toner cartridge for the Brother DCP-L2540DW printer. This toner is professionally engineered to meet or exceed the genuine specifications and quality output of the Brother TN660. It offers a printing yield of up-to 2,600 pages ideal for high-volume printing. Being able to replace your copier's toner cartridge quickly and correctly lets you get back to work faster. If you are looking for quick and easy steps on how to replace the toner cartridge in your Brother DCP-L2540DW, follow the instructions below. Step 1 - Turn on your machine and open the front cover. Step 2 - Take the empty toner out by pushing down the lock lever on the drum unit assembly. It is a good idea to grab some paper towel just in case your old toner spills so you won't have a hard time cleaning it up on your table. Wrap up the empty toner before keeping it to somewhere safely. Step 3 - Unpack the new brother toner cartridge. Try shaking it a few times carefully before removing the orange shield or protector. It is actually quite possible that the powder substance inside it has settled during storage. Shaking allows the toner powder to spread evenly on the inside. thus, getting as many page prints as possible. Step 4 - Install the new toner by putting it into the drum unit. This should just fall into its position and snap into place. Step 5 - Move the corona wire cleaner back and forth several times and put the whole thing back into the machine then close the cover. The copier will then figure out for itself and detect the new toner installed. Press the "Go" button three times to print a test page. When it's done, then you're ready to go! If you want to stock up on replacement Brother TN660 black toner cartridge, V4ink has it for you at very low prices. Just check out our website for more options. We have compatible as well as genuine replacements available for your Brother DCP-L2540DW. post comment

Troubleshooting Tips [28 Feb 2017|05:29pm] Ink Cartridges Ink cartridge is leaking. Some of our cartridges may have been overfilled by the factory. We suggest you open the cartridges at a sink or over your garbage can to avoid possible leaks from damaging your valuable items. The internal pressure in the vacuum is not balanced. The cartridge should work fine anyway. Let the cartridge sit (printhead down) on a paper towel for a few minutes, then clean it up and install. (For a high temperature area) When the cartridge is opened, the ink may be bubbling/dripping out of the cartridge if it has been in a high temperature environment for a long time. This is because the heat creates pressure within the sealed cartridge and that pressure blows the ink out when the cartridge is opened. Please try chilling the cartridge in the refrigerator (not freezer) for a couple hours before use. Cartridge has a different shape The shape of our compatible cartridges may look a little different from OEM cartridges, but they are designed for use in your printer, and will fit. My cartridge won't fit Please make sure to remove the plastic protective case from the cartridge. Low ink message showing at the printer All of our cartridges are fully filled with ink. However, there are a small number of hp ink cartridges that may not have been reset fully during the remanufacturing process. Either bypass the low ink message or disable the ink level system on your printer. Although your printer will not track the ink levels, our cartridges will print fine from start to finish. On certain Epson and Lexmark printers, if the printer is saying you cannot print due to low ink, please press and hold the "stop" or "cancel" button for 10 seconds. This will reset the counter and allow you to use the cartridges normally. The print quality is not very good or the printout contains no ink Includes most Brother, Canon, Epson, and Xerox models. Make sure that you have removed the foil or plastic strip covering the vent hole and the nozzle. (Usually a bright color, but sometimes clear.) Make sure that the vent hole at the top of the cartridge and the nozzle are unblocked by any tape or plastic strip. To ensure that the vent hole is unobstructed, use a paper clip or another small, pointed object to probe the vent for blockages. Run the head cleaning cycle 2-3 times. Please make sure that the printer is set online (at the computer) and increase the darkness setting at the printer. If the color is still off, please install a whole set of our cartridges at your printer. It is possible that the formula of our ink is different from that of your original compatible cartridge. Note that Epson printers should be turned on and used at LEAST once a month, or preferably once a week. If the printer has not been used in over 5-6 months, Epson recommends that you replace the ink cartridges. Cheap toner cartridges can be found on V4ink website. 1 comment|post comment

How to check the ink or toner levels on my printer [27 Feb 2017|10:28am] From the Systray Icon: None of the following steps work if you have not installed the software that was included with your printer. It's also important to note that every printer is different. These rules are meant as a general guideline. 1. Turn on the printer. 2. Locate the printer settings, often found by right-clicking the printer icon in the Systray, located in the bottom right-hand corner of your screen. 3. Within the printer settings software, you should see the toner levels for the currently installed printer cartridge. Below are a few different examples of how the ink level screens may look. Through the Windows Control Panel: The following steps will work for nearly any printer. However, if you have not installed the software that came with the printer, you may not be able to view the ink or toner levels. 1. Open the Control Panel. 2. Find and open the Printers option. 3. Right-click on the icon for the printer and select the Printer properties option. 4. Within the printer properties window, you can see the ink or toner levels for the currently installed hp ink cartridges. Through the Printer Menu: Keep in mind that every printer is different and the following steps are generalized. For explicit instructions on checking ink levels, consult your printer's documentation. 1. Turn your printer on. 2. Locate the Menu button and use the appropriate navigation keys to find a Status or Reports section. 3. Print a System Data or Status page to see current toner levels. If you want to order printer ink online, V4ink is the cheapest place to buy printer ink. post comment

Printer Not Recognizing Compatible Cartridges- 8 Steps To Take [23 Feb 2017|10:31am] Is your Samsung, HP, Brother, Canon, Ricoh or Epson printer not recognizing your new ink or toner cartridge? This is something that we find our customers experience every now and again so you definitely aren't alone! A printer not recognizing a new ink or toner cartridge is one of the most common issues that print owners experience when changing or replacing an empty one, irrespective of what brand printer you have, and one that our customers frequently ask us about. There may be occasions when, after installing a new ink or toner cartridge in your printer, you might see a message like: Your printer says 'toner is not compatible' Your printer says 'printer cartridge not detected' A low or empty level of ink and toner displayed on your computer A message on your printer warning "no cartridge installed" (or words to that effect) Flashing warning lights displayed on your printer Internal memory reset: Your printer should automatically recognize when you install a new cartridge and reset its internal memory, ensuring that it's displaying full ink and toner levels etc. However, sometimes the printer just doesn't do that correctly and believes that the old one, or no cartridge, is currently in there, instead. Protective strips: If you haven't removed protective covers or plastic strips that are attached to a new cartridge when you first take it out of its packaging, the printer will definitely fail to register the new cartridge. Dirty / damaged contacts: The canon printer ink or toner cartridge has a number of metal contacts that connect to similar metal contacts in the printer allowing them to communicate. Dirt or damage can prevent this. Firmware: Modern printers automatically connect to the internet but pc software or internal printer software (firmware) will often need to be updated. These updates can often fix bugs. Incorrect consumable installed: A rare occasion but this does happen! If a drum or fuser or other maintenance item was accidentally purchased instead of a toner or ink cartridge, the printer will not work and still needs a new ink or toner. So, here's what to do - 8 steps to try The first thing to do is not to panic! Whether you've bought them from us or another supplier, there really shouldn't be any reason why a good quality original or compatible cartridge wouldn't work in your printer so with a little patience, we'll get you through it. Try the following 8 steps to correct your issue. Resetting the printer memory: 1.Remove your new cartridge and replace it with the old one. Leave your printer and go and do something else for 10 minutes. 2.Replace the old cartridge with the Best Toner Cartridge again. These two steps alone often resolve the issue, so see if your printer now recognizes your new cartridges. However, if you're still having trouble. 3.Remove the new cartridge. Make sure you place it in a clean and safe place where the cartridge or the surface won't be damaged. 4.Turn the printer off button using its power button 5.Unplug your printer at the wall. It's important to do both steps 4 and 5 separately, as some printers can remain in sleep mode if you've only switched off the power button on the printer control panel. Leave your printer like this for about 10 minutes or so. 6.Plug your printer back in at the wall (but don't press the power button just yet) 7.Insert your new cartridge 8.Press the power button on your printer 1 comment|post comment

My Samsung Laser Printer Is Printing Blank Pages [22 Feb 2017|11:35am] When your Samsung laser printer begins to print blank pages, it usually means that the printer's toner cartridge is running out of toner, the cartridge is defective and needs replacing or one or more components within your printer is faulty. Troubleshooting the printing problem is not difficult; you can usually resolve the problem yourself without consulting a repair service or center. Document Issue Your Samsung laser printer will print documents containing blank pages including entire documents containing blank pages, so it's possible the problem is not with your printer but with the document you are sending to the device. Check the document and delete any blank pages to resolve the printing problem before troubleshooting your printer's toner cartridge. Sealing Tape Issue If your samsung printer cartridge was recently replaced and is printing blank pages, remove the cartridge and check to see if you removed the sealing tape inserted into the cartridge. The sealing tape keeps toner from escaping the cartridge while within the cartridge's packaging. Open your Samsung printer's front cover, pull its toner cartridge out and pull the sealing tape out of the cartridge to resolve the printing issue. Reinstall the cartridge and resend the document you are trying to print to the printer. Out of Toner Issue Your Samsung laser printer's toner cartridge doesn't last forever and the cartridge may not always alert the printer that its toner level is low. This problem will result in blank documents no matter how many times you send a document from your computer to the printer. To squeeze the last bit of toner out of your printer's cartridge, open your Samsung printer's front cover, pull its toner cartridge out and shake the cartridge gently from side to side five to six times to distribute the toner inside of the cartridge. Hold the cartridge away from you to keep any loose toner from getting on your clothing. Do not touch the underside of the cartridge - this area makes contact with your printer and contains toner. Reinstall the toner cartridge once the toner is redistributed. You will be able to use your printer for a few more cycles, but will still have to replace the cartridge. Defective Toner Cartridge If the toner cartridge's sealing tape is not present and the cartridge is full of toner but still printing blank pages, the toner cartridge is defective and needs replacing. It could be that one or more components inside of the cartridge are failing or that the cartridge's electrical components are not communicating with your Samsung laser printer. Replace the cartridge immediately and try returning the defective cartridge for an exchange or refund. If you want to order printer ink online, V4ink would be the cheapest place to buy printer ink. Faulty Printer Components A faulty or defective printer controller or one or more defective circuit boards inside of your Samsung laser printer can cause the device to print blank pages. A faulty laser shutter, transfer roller or laser scanner cable might also cause your printer to print blank pages. Consult your Samsung laser printer's owner's manual or the Samsung website for a listing of authorized repair centers you can ship or take your printer to for repair. If the laser printer is still under warranty, the repair will be free but you may have to pay for shipping the printer to the repair center. 1 comment|post comment

How to Change a Samsung Cartridge [21 Feb 2017|10:49am] One of the easiest things you can do to keep your printer printing at an optimal level is to change the toner cartridge. Even if the printer is an all-in-one, like the Samsung SCX-4500W, the process can be completed with a few easy steps. And fortunately, you don't even have to guess when the time to change the cartridge comes. This model actually tells you it's time by displaying messages on its screen and by blinking LED lights on the control panel. To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Cover it with a piece of paper, if necessary. Do not touch the green area of the toner cartridge. Use the handle on the cartridge to avoid touching this area. Do not use sharp objects such as a knife or scissors to open the toner cartridge package. They might scratch the drum of the cartridge. If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into fabric. When opening a scan unit, hold the document feeder and scan unit together. How to Change a Samsung Toner Turn the printer's power off. The power button is located on the control panel on the top of the printer, on the right side. Open the printer's top cover by pressing the top cover lever, which is located on the bottom side of the top cover. Lift the cover all of the way open. Locate the toner cartridge. It will be right in the center of the printer and has a handle on the top of it. Grab the handle and pull the cartridge out. Hold the replacement cartridge at its side and gently rock it back and forth. This will help to distribute the toner equally throughout the cartridge. Remove the paper cover from the top of the cartridge. Insert the replacement cartridge into the printer and close the printer's top cover. Finally, V4ink is the cheapest place to buy printer ink. post comment

Causes and Solutions of No Paper Feed [20 Feb 2017|10:33am] 1, the paper put too much. First check that the paper is installed in accordance with the standard, such as whether the loading position has exceeded the left arrow arrow mark on the Printer, if more, you must reduce the printing paper. 2, blockage. To see if there is any foreign matter inside the printer block, for example, if the paper appears in the printer paper, it will lead to the phenomenon of not feeding. If there is a foreign object, it must be excluded, be sure to turn off the printer power, and then carefully remove the foreign body. If you want to remove the jammed paper, the paper must be along the direction of the paper slowly pull out, remove the paper after the paper also check whether there is residual shredding, and to ensure that the shredding is also cleared. 3, printing paper and wet. If you use the paper storage time is too long, and the surface has a wet feeling, there may be no paper into the phenomenon, this time we have to do is to dry the printing paper. 4, whether the ink runs out. The black or the ink cartridge's light flashes or flashes to indicate that the ink is nearly empty. If the ink cartridge is empty, the printer can not feed paper. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink post comment

Troubleshooting of Toner LED flashing [20 Feb 2017|10:31am] I just replaced the tn450 toner cartridge and the LCD continues to display the message "Toner Low" / "Replace Toner" / "Toner Ended" or the Toner LED is still on or flashing. If the machine's display or LED continues to show the Toner Low, Replace Toner or Toner Ended error indication after installing a new toner cartridge, follow the steps below to resolve the issue. 1. Verify that you didn't replace a different consumable by mistake. The Brother machine has separate consumables - the toner cartridge and the drum unit. Verify you replace only the toner cartridge and not the drum unit. 2. Verify you are using a NEW Brother toner cartridge. When replacing the toner cartridge, you MUST install a brand new, unused genuine Brother toner cartridge in order to reset the toner status. Swapping toner cartridges from one machine to another or installing a partially used toner cartridge may cause this issue. Brother machines control their image quality for the most suitable print quality by monitoring toner consumption. If you install a partially used toner cartridge, your Brother machine is unable to recognise toner consumption correctly which will cause this issue. Therefore, when you replace the toner cartridge, use a brand new toner cartridge, not a partially used toner cartridge from another machine. 3. Verify you are using a GENUINE Brother toner cartridge. For optimum performance, use only new genuine Brother brand consumables which are specially formulated to ensure top print quality. Printing with non-Brother genuine toner cartridges may reduce not only the print quality but also the performance quality and life of the machine. If damage is caused to the drum unit or other parts of the machine as a result of using hp ink cartridges, any repairs required as a result will not be covered by the Brother limited warranty. 4. Verify the toner cartridge is installed correctly. If you install a new genuine Brother toner cartridge but the "Toner Low", "Replace Toner" or "Toner Ended" error indication remains, the toner cartridge may not be installed correctly. Reinstall the toner cartridge, referring to the instructions on how to replace the toner cartridge. 5. Clean the corona wire. This issue may have occurred because the corona wire has become dirty. 6. Update the firmware to the latest version. Go to the Downloads section of this website to check the latest version of the firmware. If you see the Firmware Update Tool in the Downloads section, check detail information to identify the firmware version. If the firmware version of your Brother machine is earlier than the latest version, update the firmware. Follow the installation instructions on the download page. 1 comment|post comment

Printer paper jam and its solution [17 Feb 2017|01:40pm] Printer toner in the course of frequent use, often can not handle the paper failure, mostly paper jam, not into the paper, a paper into the multi-page and the phenomenon of random paper. How do these failures to deal with it after that? 1, the paper surface is smooth. If the phenomenon of paper jams, first of all should see the paper surface is flat, if there is paper curl or fold phenomenon, it is best to use the surface smooth, smooth paper, and to ensure that the printing paper surface can not have a similar plastic adhesive. 2, the paper is too thin or too much. Must ensure that the quality of printing paper more than 60 grams or more, the paper is too thin will cause the printer to become difficult when you take the paper, the printer is likely to cause a paper jam. And once into the printing paper can not be too thick. 3, the pickup roller wear. The pick roller is the most wearable part of the printer. When the Sheng tray of normal paper, and can not take the paper, the paper roller is often wear or spring loose. Pressure is not enough, the paper can not be fed into the machine. Pickup roller wear, can not be replaced at the moment, the available wound rubber band approach for emergency treatment. Winding rubber band, the increase in the rubbing friction, make paper back to normal. 4, other. Sheng tray is not properly installed, the paper quality is not good (too thin, too thick, wet), also may cause a paper jam or can not take the fault. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink 1 comment|post comment

How to Replace a Toner Cartridge in a Laser Printer [16 Feb 2017|04:17pm] Printer cartridge eventually run out of ink after continued use. Being able to replace them swiftly and correctly lets you get back to work faster. If you want to learn how to replace a toner cartridge in a laser printer, follow these steps. 1. Turn on the printer by pressing the power button. You have to have the device on to access brother toner cartridge of most units. 2. Open the printer door to access the toner cartridges. In some models, you will have to press and hold the release button and pull the lid toward you. When the cover is lifted on most laser printers, the carriage automatically slides to the right side of the unit for easy access to the cartridges. 3. Remove the spent cartridge from the printer. Depending on the model, you may have to unhook the cradle holding the cartridge in place, or press the release tab inward to unlatch the cartridge you want to remove. With some printers, you may have to hold down the blue release button at the side of the cartridge carriage. Once unlocked, remove the cartridge by pulling it up and toward you. 4. Take the new cartridge out of the box, but keep it in its plastic packaging. Sometimes, during shipping, ink can settle in the toner drum, resulting in poor-quality copies. To prevent this problem, gently shake the cartridge. This helps fully distribute toner throughout the cartridge. 5. Remove the new cartridge from its packaging and pull the colored tab on the cartridge. This removes the protective tape from the bottom of the cartridge. While doing this, be careful not to touch the imaging drum on the bottom of the print cartridge. Smudges on the drum can cause print-quality problems. 6. Put the replacement cartridge in. It should snap in place securely. On devices with a locking cradle, be sure to snap it shut around the cartridge before closing the lid. 7. Your printer is ready to be used. Print a test page. Your computer will automatically recognize that a new hp ink cartridges has been installed. Most computers will ask you if you want to print a test page to ensure that the new cartridge is functional. Click "OK." The computer will scan the printer settings and eventually produce a full-color page. post comment

Printer common jam resolution [16 Feb 2017|04:15pm] General Printer toner the most common fault is a paper jam, a lot of jam problems with the user's use of a relationship, for example, the paper is not put away is easy to jam and so on. If the user can learn some simple skills to deal with jam problems, then in everyday applications, it is easy to improve office efficiency. Here I share several common problems for the jam and solutions. A multiple sheets feed reasons 4 　　 1, the position of the paper. Position paper was placed incorrectly can cause multiple sheets feed occurs, correct height of the paper can not be higher than the arrow mark paper slot on the left rail; secondly, check the paper specifications meet the requirements: 60 to 180 wt. g paper in order to meet requirements, and less than 60 grams of thin paper, it is prone to the phenomenon of simultaneous multi-feed. 　　 2, the surface of the printing paper curl. Curl is also caused by the occurrence of a multi-page paper, it must ensure that the paper surface smooth, if slightly curled, you can think of ways to flatten it. 　　 3, electrostatic induction of. Electrostatic induction can also cause the phenomenon of multiple pages at a time, must be installed in the paper before the paper to spread out in a fan-shaped way to ensure that each paper can be separated separately, and then press the correct way to load paper into the guide In the bin. 　　 4, adjust the position of the lever. For printers with paper thickness adjustment, it is important to adjust the position of the adjustment lever. When using a different paper, paper thickness lever position is not the same, for example, when using a conventional thickness of the paper, you must adjust the position of "0" bar. Of course, different printers on the regulation of the adjustment lever is not the same, the best reference manual. When the printer to take the paper to print to a page when a piece of paper suddenly empty, and then automatically followed by printing down. This is often the printer to use for a long time, paper detection switch contacts due to wear and dust into the poor contact, resulting in the printer to make the wrong reasons to judge. Remove the printer, find the paper detection switch carefully cleaned with alcohol, can be restored to normal. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink 1 comment|post comment

How to Replace Your Samsung Printer Cartridges [15 Feb 2017|04:30pm] Part of saving time is just being prepared. When an ink cartridge runs out, you don't want to have to drop everything and run to the store. If your office uses Samsung printers and supplies, you may want to get acquainted with Samsung printer cartridge replacement. When it's time to swap out an old printer cartridge, you can save time by following some simple steps. Here are some simple instructions for replacing your Samsung printer cartridges, so you can get back to printing. Replacing Printer Cartridges: 1. Open the printer utility software. Samsung tries to make replacing samsung printer cartridge simpler by automating most of the steps for you. Explore your printer utility software and learn a bit more about how it works. To replace one of your Samsung printer cartridges, you'll need to open the cartridge replacement utility. 2. Move the cartridge head into place. Have your Samsung printer cartridges ready and follow the utility instructions to move the cartridge head into place. 3. Remove the old ink cartridge. Open the panel concealing the printer head and the old Samsung printer cartridges. Release the clips holding the empty one and pull it out. Remember to recycle your old Samsung printer cartridges. Samsung may even buy them back. 4. Prepare the new cartridge. Remove the appropriate Samsung printer cartridges from the packaging and shake them vigorously. 5. Insert the new cartridge. Remove the tag from the bottom of each Samsung ink cartridge, being careful not to touch any contacts or circuitry. Slip each cartridge into its space and press down until it clicks into place. 6. Close the printer. Close the printer lid or panel. The printer head should slide back into place and start charging your new cartridges. Samsung Printer Cartridge Tips: 1. Samsung may recycle your hp 201x toner, or you can donate them to local recycling programs. 2. Unless your printer is malfunctioning, avoid printing test pages that can use a lot of ink. post comment

Installation instruction of Brother TN420/TN450 [15 Feb 2017|04:26pm] These instructions explain toner installation procedures for a brother tn420 / tn450 toner cartridge. The original toner cartridge that was included with this machine may either be a starter, standard, or a high yield cartridge. When the toner becomes low, the TONER LED indicator light will flash continuously until replaced. Once the toner cartridge is empty, the printer will enter a “REPLACE TONER” mode that ceases print functionality until the toner cartridge is replaced. A new and unused toner cartridge will reset the “REPLACE TONER” mode. Before you begin please take time to perform the following steps to ensure that the new print cartridge is properly detected by your Brother printer: 1. Check to ensure that the dial on the left side of the brother toner cartridge is in the position as illustrated in the image below. If not, turn the dial counter clockwise until it matches the position in the image. 2. Check to make sure that the printer is powered up during the entire process. Changing the cartridge with the printer powered off will not reset the “REPLACE TONER” mode. In the event that the printer is powered off when the cartridge is installed, you will need to remove the cartridge and repeat step one before reinstalling the cartridge. Replacing the toner cartridge 1. Make sure that the machine is powered up. 2. Open the front cover of the machine. 3. Remove both the drum unit and toner cartridge assembly. 4. Push down the green lock lever and take the toner cartridge out of the drum unit. 5. Unpack the new toner cartridge. Hold the cartridge level with both hands and gently shake it from side to side several times in order to distribute the toner evenly inside of the cartridge. 6. Pull off the protective cover. 7. Note: Before installing this cartridge, please check to ensure that the dial on the left side of the new cartridge is positioned identical to the image below. If not, turn the dial counter-clockwise until it matches the dial position in the image. It is imperative that this dial be locked into position as illustrated to ensure that the printer detects that a new cartridge has been installed and resets the “REPLACE TONER” mode. 8. Put the new toner cartridge firmly into the drum unit you hear and feel it lock into place. If installed successfully, the green lock lever will lift automatically. 9. Clean the primary corona wire inside of the drum unit by gently sliding the green tab from right to left and left to right several times. 10. Reinstall the drum unit and toner cartridge assembly back into the machine. Close the front cover. 1 comment|post comment

Replacing the Toner Cartridge for HP Color LaserJet [13 Feb 2017|11:59am] This printer indicates when the hp ink level is low. The actual toner cartridge life remaining can vary. Consider having a replacement cartridge available to install when print quality is no longer acceptable. This printer uses four colors and has a different toner cartridge for each color: yellow (Y), magenta (M), cyan (C), and black (K). The toner cartridges are inside the front door of the printer. Do not remove the toner cartridge from its package until it is time to install it. To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. If you remove the toner cartridge from the printer for an extended period of time, place the cartridge in the original plastic packaging, or cover the cartridge with a light-weight, opaque item. If toner gets on your clothing, wipe it off with a dry cloth and then wash the clothes in cold water. Hot water sets toner into fabric. Information about recycling used toner cartridges is in the toner cartridge box. Follow these steps to replace the hp printer cartridges in your printer. 1. Open the front door. 2. Grasp the blue handle on the toner cartridge drawer, and then pull out the drawer. 3. Grasp the handle on the toner cartridge, and then pull the toner cartridge straight up to remove it. 4. Remove the new toner cartridge package from the box, and then pull the release tab on the packaging. 5. Remove the toner cartridge from the opened packaging shell. 6. Grasp both ends of the toner cartridge, and then gently rock the cartridge back and forth to distribute the toner. 7. Do not touch the imaging drum on the bottom of the toner cartridge. Fingerprints on the imaging drum can cause print quality problems. 8. Insert the new toner cartridge into the drawer. Make sure that the color chip on the cartridge matches the color chip on the drawer. 9. Push the toner cartridge drawer into the printer. 10. Close the front door. 1 comment|post comment

How do I clear the message "Replace Toner"? [13 Feb 2017|11:57am] The message "Replace Toner" is intended to alert you that the toner cartridge has reached the end of its expected life. It is recommended that the toner cartridge be replaced. To clear the "Replace Toner" message, install a new genuine Brother TN420 or tn450 toner cartridge. When replacing the toner cartridge, you MUST install a brand new, unused genuine Brother toner cartridge in order to reset the "Replace Toner" status. Do NOT install a previously used cartridge that was already installed into another machine or a TN starter cartridge that comes with the machine. Refer to the following solution for toner replacement instructions - "How do I install a new toner cartridge? How do I replace the toner cartridge?" The machine can be placed in Continue Mode. This is a temporary mode that will ensure that the current toner cartridge can continue to be used until the status changes to "Toner Ended" before you install a new toner cartridge. Refer to the following solution for instructions to enable Continue Mode - "What is Toner Continue Mode?" Brother strongly recommends that customers use only genuine Brother drum units and/or toner cartridges. Each Brother laser printer is designed to work at pre-set temperatures that are matched exactly to each of our individual toner formulations. Each individual component is designed to work with the other to ensure quality and reliability. Using non-Brother supplies may affect the hardware performance, print quality, and machine reliability. The Brother limited warranty does not apply to any problem that is caused by the use of third party drum units, ink cartridges, or toner. 1 comment|post comment

Get familiar with printer supplies-teach you how to repair the drum [09 Feb 2017|03:13pm] Toner to the toner is to reduce the cost of printing the most important method. But the more the number of plus toner, toner cartridges will print quality is getting worse, generally when applied toner over two times, three times, when there will be some regular black spots, and this issue will With the increase in the number of print more and more serious. Finally, there will be printed documents blurred or print out a black mark, this time, the cartridge to scrapped, abandoned it is a pity, leaving useless, most people will choose at this time to replace the new cartridge. In fact, the old cartridge is still available, there are ways to repair, that is, renewable friends. Repaired after the print cartridge quality can also be comparable with the original cartridge, and the cost is only about a quarter of the original cartridge price. This is in line with environmental requirements, but also save our money. Hearing here, is not already heart it! Well, now let us together to waste cartridges to a "back to life." In fact, repair cartridge method can be divided into new toner and replace the photosensitive drum two parts. Following on in the usual HP 6L printer cartridges, for example, how we provide a method of regenerating the drum. First of all, to cut off the power to the printer, remove the print cartridge from the printer (this is of course, or else how to regenerate it), then pinch the side of the metal pin with a diagonal clamp, carefully pull out (or With metal nails pin into the cartridge, open the cartridge can be taken out after the metal pins), silver metal pins on both sides can be pulled out after the cartridge is divided into two parts, a light blue photosensitive selenium is a collection of waste powder part, While the one with the magnetic roller is the part for powder. And then part of the magnetic roller for the non-rotating side of the magnetic roller screw unscrew, take the plastic shell can be seen after a plastic cover, open the plastic cover, the toner cartridge and the magnetic roller on the clean up all the toner, Be sure to clean up all the residual toner, it is best to use a vacuum cleaner net absorption. Then the magnetic roller in the reverse order of just the right, this time should be held down by the magnetic roller to prevent the magnetic roller from the original position. The toner shaken slowly into the powder for the warehouse, a good plastic cover and plastic shell should pay attention to the magnetic roller on the axle at the end of the semicircle and plastic shell on the semi-circular holes on the good. Gently rotate the gears on the sides of the magnet roll to make the toner even. Now comes the most important step - the replacement of the new drum. The waste toner fixing pin fixed portion of the photosensitive drum with diagonal pliers to pull out (this can not be fixed with nails to pin into the drum where yo!), You can remove the old drum pulled out after fixing pin, and then the waste Powder collection part of the waste powder clean up. According to the demolition of anti-order put on a new drum, photosensitive drum installed to note that there is about the points, there will be side of the gear groove mounted groove. Then, fix the pin to fix the photosensitive drum. Newly purchased photographic drums have a black anti-exposure seal, do not torn off before installation to prevent exposure, to be installed after the check can be torn off. Finally, the powder part and the waste collection part of the open position by the installation of recovery, plug the metal on both sides of the card, you can start printing. Printer ink refill, help you print high-quality documents, photos, and graphics. Cheapest place to buy printer ink: v4ink.com post comment

navigation [ viewing | 20 entries back ] [ go | earlier/later ]